PDF Electric and Supply

1-800-360-6802
1-919-535-3180
sales@pdfsupply.com

IC660BBA020

Buy NowIC660BBA020
IC660BBA020
IC660BBA020 Wiring

Rated 4.7/5 based on 14 ratings.
  • IC660BBA020
  • IC660BBA020 Wiring

Product Description


The IC660BBA020 is a voltage/current analog block in the GE Fanuc Genius I/O series. It has four input and two output circuits. Two types of analog blocks are available with a power supply of 115 VAC and 24/48 VDC. IC660BBA020 supports five analog ranges: 0-10 volts DC; -10 volts DC to +10 volts DC; -5 volts DC to +5 volts DC; 0-5 volts DC; and 4-20 mA/1-5 volts DC. The internal power supply of this block can drive a current load of 300 Ohms.  Configurable block features include independent scaling; fault reports which can be enabled or disabled depending on input/output; selectable input filter time up to 1024ms; powerup default values for each output; and Low/High Alarm detection, among others.

 

IC660BBA020 is compatible with any handheld monitor IC66*HHM500, though HHM501 requires a change in configuration. The serial bus uses terminals 1 to 4 with AWG wires. Field devices use terminal 5 to 32 with AWG wires. Terminals 6 (DC+) and 7 (DC-) connect the power source to the 24/48 VDC. H and N terminals connect  the 115 VAC block with the 250V, 1/8Amp slow blow fuse. Terminals 5, 12, 28, and 20 are for ground. Three terminals named common are for a source. The user can connect input voltage device between V+ and IN and V- and RTN terminal in series. The user can connect output voltage device to terminals COM and VOUT. JMP terminal is for jumper connection. Terminals I+ and I- are for the current mode.  The first four input circuits convert incoming current or voltage signal to digital count with optional scaling. Circuit numbers 5 and 6 give output scaled digital count from CPU. I/O Enabled and Unit OK LEDs indicate the operating status of the block. The diagnostics system indicates fault messages.


Technical Specifications


Rated Voltage: 24/48 VDC 
# of Points: 4 Inputs / 2 Outputs
Input Range: 0-10 VDC, -10 to +10 VDC, -5 to +5 VDC, 0-5 VDC, 4-20 mA 
Output Range: 0-10 VDC, -10 to +10 VDC, -5 to +5 VDC, 0-5 VDC, 4-20 mA
Operating Voltage: 18 - 56 VDC
Points per Common:   One group of 4 Inputs and one group of 2 Outputs

 

GE Intelligent Platforms / GE Fanuc GE-IP Genius I/O

SKU 2172241  UPC 0799705802971

Part Number: IC660BBA020 / ic660bba020
Mfr/Brand Name: GE Automation
Mfr Number: IC660BBA020 / ic660bba020
Type: 24/48 volt DC, Voltage/Current Genius Analog I/O Block

Troubleshooting and Product Information for IC660BBA020

Download product information, troubleshooting guides and operation manuals to get your PLC operational.

New IC660BBA020
Price: $3,416
5 In Stock
1 Year PDF Supply Warranty

*Need a Specific Revision?

New Surplus IC660BBA020
Price: $2,750
8 In Stock
3 Year PDF Supply Warranty

*What is New Surplus?

Save
 20%
Reman IC660BBA020
Price: $395
98
In Stock

2 Year PDF Supply Warranty

*What is Remanufactured?

Save
 89%
Repair Your IC660BBA020
Price: $295
1 Year PDF Supply Warranty
Call For Assistance
1-800-360-6802

Other IC660BBA020

Available Revisions:

Confirm Your Revision Number

1C660BBA020 , GEFIC660BBA020 , CIMIC660BBA020

Specification

Block Type:

CatalogNumbers:

115 VACAnalogI / OBlock TerminalAssemblyonly ElectronicsAssemblyonly

24 / 48VDCAnalogI / OBlock TerminalAssemblyonly ElectronicsAssemblyonly

4input / 2outputcircuits

IC660BBA100

IC660TSA100

IC660EBA100

IC660BBA020

IC660TSA020

IC660EBA020

Size (height x width x depth): Weight:

LEDs (block):

Block to Block Isolation: HeatDissipation:

8.83” (22.44cm) x 3.50” (8.89cm) x 3.94” (10.00cm)

4 lbs. (1.8 kg)

UnitOK,I / OEnabled 1500 V

6 Watts

Block Power(nominal):

Operating range Maximumpower Frequency / ripple

Power supply dropout time

115 VAC

98–132 VAC

10 VA

47–63 Hz

1 cycle

24/48 VDC

18–56

8W

10% max. ripple 10mS

Common mode rejection: Commonmodevoltage:

60 dB (0–1 KHz)

170volts,maximum

Absoluteaccuracy  (at 25C):

Typical: 0.2% of full scale; Maximum: 0.5% of full scale:

within 50mV on the 10 volt range, 25mV on the 5 volt range, and 100mA on the 4 to 20 mA range.

Thermaldrift  (from 25C):

Typical:  10 PPM per C; Maximum: 40 PPM per C

Circuit range selections:

0–10  VDC,  10 VDC, 5 VDC, 0–5 VDC, 4–20 mA (or 1–5 VDC)

InputCharacteristics:

Inputresolution

Input update frequency Input filter ranges Inputdiagnostics

 

12 bit + sign Once every 4mS

none, 8, 16, 32, 64, 128, 256, 512, 1024mS

Underrange, Overrange, High Alarm, Low Alarm, Open Wire

OutputCharacteristics:

Outputresolution

Output update frequency Outputdiagnostics Output load

 

12 bit + sign Once every 4mS

Underrange, Overrange.

Voltage mode: 2000 or greater; Current mode: 0 to 300

Environmental:

Operatingtemperature Storagetemperature Humidity

Vibration

 

0   to   60C   (+32  to 140F)

–40   to    +100C   (–40   to   +212F)

5% to 95% (non–condensing)

5–10 Hz 0.2” (5.08mm) displacement; 10–200 Hz at 1G

 

Troubleshooting IC660BBA020

Troubleshooting information is available on IC660BBA020's website page; it also includes a datasheet, a user manual, and a wiring diagram.

 

Repair your IC660BBA020

PDF Supply can repair your IC660BBA020 in 3-5 business days. And PDF Supply stands by all of its repairs with a 1 year customer satisfaction warranty.

Customer Questions and Answers


  • Question:  What is an IC660BBA020?  Answer:  The IC660BBA020 is a 24/48 VDC Voltage/Current Analog I/O Block of the GE Fanuc Genius I/O Series. This block has 4 independent input circuits and 2 independent output circuits. 
  • Question:  What is the difference between IC660BBA020 and IC660BBA100?   Answer:  The only difference between these blocks is their power supply. 
  • Question:  Can I use the IC660HHM501 Hand Held Monitor for the configuration of IC660BBA020?   Answer: Yes, you can. 
  • Question:  What should the baud rate be set at when configuring this block?   Answer:  It should be set at 153.6K standard. 
  • Question:  When I press the leads against "in" and "return", what should be happening?   Answer:  You should be looking for a reading and if all the values of all your settings are the same then all your readings should be the same. (Tip: Make certain that all the screws are screwed down very tight to make sure the connections can happen accurately.)
  • Question:  When checking the output, where should the black and red leads go?   Answer:  Black should be on common and red (or positive) should be on voltage out. 
  • Question:  What is important about checking the outputs?   Answer:  It is important to make sure that the output can be on or off whatever value that you put in it.
  • Question:  When you have the CPU in run mode, what should happen?   Answer:  The Enabled LED should come on to let you know the block is enabled. This also means that the port is communicating. It lets you know the block is working properly and if you want to, you can force the inputs and outputs off or on using Proficy Machine Edition. 
  • Question:  What would indicate something is wrong with my IC660BBA020?   Answer:  If you power it up and it doesn't have any lights on at all, then your IC660BBA020 may need repair

For more information on the IC660BBA020 Voltage/Current Analog I/O Block of the GE Fanuc Genius I/O Series, please see the Datasheet User-Manual.

IC660BBA020 is a Phase B GE Genius block and is compatible with all GENIUS supported PLC systems. The earlier version- IC660CBA020 is a Phase A GE Genius Block and is only compatible with Series Six and Series Five PLCs.

 

The final letter in the part number (ex. IC660BBA020K) indicates the revision. Revision K and later use the newer style electronic housing and therefore need the newer style plastic door and may indicate some compatibility issues with the terminal strip.

Need To Order A Specific Revision?

Give us a call at 1-800-360-6802 or 1-919-535-3180.

We can help you with your Revision specific needs.


Free Overnight delivery on orders over $500!

What is New Surplus?

These “New Surplus” units are a great cost saving alternative. This product is sealed in the original manufacturer’s packaging with all sub-assemblies and documentation. May indicate older date code. Comes with a PDF Supply 3-year warranty.


Free Overnight delivery on orders over $500!


What is Surplus New?

Surplus New - New unused and includes all sub-assemblies and documentation. Product may ship in manufacturer or PDF Supply packaging. May indicate older date code. Includes a PDF Supply 3 Year Warranty.


Free Overnight delivery on orders over $500!


What is Reconditioned?

Reconditioned products from PDF Supply are a cost-effective alternative to new and obsoleted PLC products. Every part is reconditioned down to the circuit board level and updated to the latest revision. All parts are thoroughly inspected and hand-cleaned before being functionally tested in a fully configured system.


Our Reconditioned Products always come with a PDF Supply 2-Year Warranty.

Free Overnight delivery on orders over $500!


What is a Verified Substitute?

A verified substitute new product is a "drop in" replacement designed with identical specifications as the OEM product. It will meet all electrical and dimensional charactertics at a substanstially reduced price.


Free Overnight delivery on orders over $500!


Download Lastest Documentation


Please visit this manufacturer's website to download the lastest manuals and datasheets.


Lowest Price Guarantee


We stand behind our prices with a lowest price guarantee. If you find a legacy GE PLC part advertised for less on an authorized GE PLC distributor website, simply contact us and send us a link to the lower advertised price. We will match that price and ship overnight FREE. The item must be in stock, in similar condition and be able to ship same day.

Free Shipping



FREE Overnight Delivery for Continental US orders over $500!

FREE Ground Delivery for Continental US orders under $500!

US orders placed Monday - Friday before 5pm EST will ship same day.

Canada/Mexico orders placed Monday - Friday before 3:30pm EST will ship same day.

International orders will ship the following business day.