GE / IP FANUC Series 90/30 In Stock

World's Largest Warehouse

of GE 90-30, Genius, and RX7i

Mon-Fri 8AM-5PM EST



Rated 4.6/5 Based on 23 ratings.

Rate your purchase of the IC660BBA021

SKU 2174159  UPC 0799705802551

All product names, trademarks, brands and logos used on this site are the property of their respective owners. PDF Supply is not an authorized distributor, reseller or representative of the products featured on this website. The depiction, description or sale of products featuring these names, trademarks, brands and logos is for identification purposes only and is not intended to in indicate any affiliation with or authorization by any rights holder.

PDF Supply is NOT an authorized distributor for this manufacturer and therefore the manufacturer’s warranty does not apply. Product comes with PDF Supply's 1-year, 2-year, or 3-year warranty.

Common misspellings:
  • 1C660BBA021
  • IC66oBBA021
  • IC6608BA021
  • IC660B8A021
  • IC660BBAo21
  • IC660BBA02l
  • IC660BBA021

Technical Specifications for IC660BBA021

ManufacturerGE Fanuc
SeriesGenius I/O
Part NumberIC660BBA021
Product TypeRTD Input Block
Voltage TypeDC
Operating Voltage12 to 24 Volts DC
Weight4 Pounds
Dimensions9 x 3 x 4 inches
HHM ConnectionsSupported
Number of Inputs6

Product Description


General: The IC660BBA021 is a 24/48 volt DC RTD Input Block from the GE Fanuc Genius I/O Series. This block monitors temperature input from Resistive Temperature Detectors (RTDs). The IC660BBA021 block groups input circuits in three rows, each with two circuits.


Input Circuits: Each input circuit can be used with RTDs made from platinum, nickel, or copper. It has sensors in place to report input data to the CPU in engineering units of tenths of degrees Celsius, tenths of degrees Fahrenheit, tenths of Ohms, or counts, depending on how it is configured.


Calibration: The IC660BBA021 is factory-calibrated to detect temperature variations as low as one-tenth of one degree. Because it is factory-calibrated, it does not require subsequent recalibration.


Resistance: The IC660BBA021 measures resistance from 0 to 5,000 ohms. Values for parameters can be set such as input filter time, alpha type, alarm thresholds, linearization, and RTD resistance.


Measures: The IC660BBA021 is 8.83” (22.44cm) high, 3.5” (8.89 cm) wide, and 3.94” (10 cm) deep. Unit OK and I/O Enabled LEDs conveniently display block status.


Troubleshooting: Diagnostic software in the IC660BBA021 automatically captures the reasons for installation or run-time errors. These errors might be electrical shorts, wiring mistakes, range threshold violations, or alarm conditions. To facilitate troubleshooting, they trigger abbreviated but easily understandable messages such as “Overrange”, “Input Shorted”, “Internal Fault detection”, “Overrange and Underrange”, as well as High and Low input alarms on a handheld monitor. Fault reporting can be enabled or disabled circuit by circuit.


Note: Severe radio frequency interference in the environment (10 V/m or higher as described in IEC 801-3 of 1984) will degrade the accuracy of block measurements without generating error messages. It is important to note that the IC660BBA101 is identical to the IC660BBA021 block except it features a power supply capable of working with a higher voltage range (115 VAC/125 VDC).


Technical Specifications


Rated Voltage

24/48 VDC

# of Points





Platinum, Nickel or Copper RTDs

Operating Voltage

18 - 56 VDC

Points per Common

3 groups of 2


Need more help?

Email us at sales@pdfsupply.com

You can order the the IC660BBA021 directly from our website.  

All orders placed Monday - Friday before 3:30pm EST will be shipped same day.

Free UPS Ground Shipping!  

We also offer repair services for the IC660BBA021.

Email us at sales@pdfsupply.com or Request a Formal Quote for IC660BBA021.


The IC660BBA021 input block is an RTD input block that has been designed and manufactured by GE Fanuc in the Genius I/O series. It comes with 6 input channels and it has a resolution of 0.1 degrees Celsius for each input channel. This input block also has 2 circuits, each of which can support 3 inputs. The IC660BBA021 RTD input block supports both block to block isolation and group to group isolation. The input block’s block to block isolation rating is 1500 Volts and its group to group isolation rating is 300 Volts. The IC660BBA021 RTD input block runs on a block power voltage rating of 12 to 24 Volts DC. It weighs 4 pounds and its dimensions are 9 x 3 x 4 inches. This RTD input block is designed to be as light and compact as possible without sacrificing any of its power or reliability.


The GE Fanuc Genius I/O IC660BBA021 RTD input block is used to monitor the temperature ratings that it receives from other RTD input blocks in the Genius I/O system. It can work with nickel RTDs, copper RTDs, or platinum RTDs. This input block comes with diagnostics software that can detect wiring errors, electrical shorts, and range threshold errors such as overrange errors and underrange errors. If the IC660BBA021 RTD input block is connected to a handheld monitor or HHM, this monitor can receive alarm messages that are sent to it by the diagnostics software. Each individual input on the block can be enabled to generate fault reports, or disabled from doing so.

Technical Information


Block Type: CatalogNumbers:

115 VAC / 125VDCRTD Block

TerminalAssemblyOnly ElectronicsAssemblyOnly

24 / 48VDCRTD Block

TerminalAssemblyOnly ElectronicsAssemblyOnly

6 RTD–compatible inputs, 3 isolated groups of 2







LEDs (I/O Block):

UnitOK,I / OEnabled

Size (height x width x depth):

8.83” (22.44cm) x 3.50” (8.89cm) x 3.94” (10.00cm)


4 lbs. (1.8 kg)



Block to Block Isolation:

Group to GroupIsolation:

1500 V

300 V

115VAC/125 VDCblockpower:

115 VAC 125 VDC


93–132  VAC @ 7W 105–145 VDC  @ 7W

47–63 Hz 10% max. ripple

Power supply dropout time:

1 cycle 10mS

24/48 VDCblockpower:



18–56 VDC @ 7W, 10% max. ripple

Power supply dropout time:




Absolute accuracy (at 25C) Platinum or Nickel:

10 Copper:

Input update frequency Input filter ranges (per block) RTDlinearization

Resistancemeasurementrange Diagnostics


0.1  C

0.5 C typical, 1.0C   maximum

5C  typical,  ”10C maximum

Once every 400 ms, 800 ms, or 1600 ms

400 ms, 800 ms, 1600 ms

Platinum (DIN 43760), Nickel (DIN 43760), Copper, Linear

0 to 5000

Input shorted, Internal fault, Wiring error, Open wire, Overrange,

Underrange, High Alarm, Low Alarm




0C   to   +60C   (32F   to  +140F)


–40C   to   +100C   (–40F   to   212F)


5% to 95% (non–condensing)


5 – 10 Hz 0.2” (5.08mm) displacement, 10–200 Hz at 1G


Troubleshooting IC660BBA021

Troubleshooting information is available on IC660BBA021's website page; it also includes a datasheet, a user manual, and a wiring diagram.


Repair your IC660BBA021

PDF Supply can repair your IC660BBA021 in 3-5 business days. And PDF Supply stands by all of its repairs with a 1 year customer satisfaction warranty.


Configure CPU Redudancy
Description: When in redundancy mode configuration, you cannot select standby or none.
Resolution: This is a typo in the manual. "Hot Standby" only applies to output data so the block will know that it can receive outputs from two different bus controllers.

Customer Questions and Answers

  • Question:  What is an IC660BBA021?  Answer:  The IC660BBA021 is a 24/48 VDC RTD Input Block from the GE Fanuc Genius I/O Series. This block monitors temperature inputs from Resistive Temperature Detectors (RTDs).
  • Question:  What is the difference between IC660BBA021 and IC660BBA101?  Answer:  The only difference between these blocks is their power supply.
  • Question:  Can I use the IC660HHM501 Hand Held Monitor for the configuration of IC660BBA021?  Answer:  Yes, you can. 
  • Question:  What should the baud rate be set at when configuring this block?  Answer:  It should be set at 153.6K standard. 
  • Question:  When I press the leads against "in" and "return", what should be happening?  Answer:  You should be looking for a reading and if all the values of all your settings are the same then all your reading should be the same. (Tip: Make certain that all the screws are screwed down very tight to make sure the connections can happen accurately.)
  • Question:  When you have the CPU in run mode, what should happen?  Answer:  The Enabled LED should come on to let you know the block is enabled. This also means that the port is communicating. It lets you know the block is working properly and if you want to, you can force the inputs and outputs off or on using Proficy Machine Edition. 
  • Question:  What would indicate something is wrong with my IC660BBA021?  Answer:  If you power it up and it doesn't have any lights on at all, then your IC660BBA021 may need repair

For more information on the IC660BBA021 RTD Input Block of the GE Fanuc Genius I/O Series, please see the Datasheet User-Manual.

The final letter in the part number (ex. IC660BBA021K) indicates the revision. Revision K and later use the newer style electronic housing and therefore need the newer style plastic door and may indicate some compatibility issues with the terminal strip.

ST. LOUIS, Feb. 1, 2019 – Emerson today announced it has completed the purchase of Intelligent Platforms from General Electric.

Common related search terms: ConfigurationDatasheetEmersonManualPDFPLCPriceRepairSpecificationTroubleshootUser-ManualWiring


PDF Supply sells used surplus products. PDF Supply is not an authorized distributor, affiliate, or representative for the brands we carry. Products sold by PDF Supply come with PDF Supply’s 1-year, 2-year, or 3-year warranty and do not come with the original manufacturer’s warranty. Designated trademarks, brand names and brands appearing herein are the property of their respective owners. This website is not sanctioned or approved by any manufacturer or tradename listed.

Rockwell Disclaimer: The product is used surplus. PDF Supply is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because PDF Supply is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, PDF Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. PDF Supply also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. PDF Supply also makes no representations as to your right to install any such firmware on the product. PDF Supply will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.