GE / IP FANUC Series 90/30 In Stock
Manufacturer | GE Fanuc |
---|---|
Series | Genius I/O |
Part Number | IC660BBA100 |
Product Type | Analog I/O block |
Inputs | 4 voltage inputs |
Outputs | 2 current outputs |
Voltage | 115 Volts AC |
Isolation | 1500 Volts block to block |
Weight | 4 pounds |
Heat Dissipation | 6 Watts |
IC660BBA100 is an analog I/O Block from the GE Genius series. The block has a rated voltage of 115 VAC Voltage/Current. The IC660BBA100 block has four independent input circuits and two independent output circuits. This block is quite flexible, which allows compatibility with a wide variety of analog I/O devices. Each circuit on IC660BBA100 Block can either receive or deliver signals in any of these five analog ranges: -5 volts DC to +5 volts DC, -10 volts DC to +10 volts DC, 0-5 volts DC, or 4-20 mA/1-5 volts DC, 0-10 volts DC.
The other remaining two are output circuits served by a 12 bit digital to analog (D/A) converter. IC660BBA100 block then converts the engineering units output received from the processor to a digital count value. It then converts the counted value to an output signal voltage. Accuracy is within 50mV on the 10V range and 5mV on the 5V range and 100uA on the 4-20mA range.
Other IC660BBA100 features include the ability to independently scale for each individual input and output; the ability to either enable or disable fault reports to the host for each input and output; inputs that can function either in normal analog input mode, or report just its alarm status; low and high alarm limits for each input both in normal input mode and alarm input mode; power default values for both output; outputs that can consequently be configured to hold last state or default if communication from the processor is lost; and input Low Alarm and High Alarm detection.
Rated Voltage: | 115 volts AC |
# of Points: | 4 Inputs / 2 Outputs |
Input Range: | 0-10 VDC, -10 to +10 VDC, -5 to +5 VDC, 0-5 VDC, 4-20 mA |
Output Range: | 0-10 VDC, -10 to +10 VDC, -5 to +5 VDC, 0-5 VDC, 4-20 mA |
Operating Voltage: | 98 - 132 VAC |
Points per Common: | One group of 4 Inputs and one group of 2 Outputs |
The IC660BBA100 Genius I/O block is a GE Fanuc analog I/O block with 4 voltage inputs and 2 current outputs. It is powered with a nominal voltage of 115 Volts AC. It is installed with the terminal assembly of the Genius I/O PLC system. The analog I/O block comes in a compact size with dimensions of 8.83 inches in height, 3.34 inches in width, and 3.91 inches in depth. It weighs 4 pounds. The front side of the IC660BBA100 block has an LED indicator that shows the “Unit OK” status and “I/O Enabled” status during operation. With an open enclosure, the block is designed for indoor use only. A block to block isolation voltage is present and it is rated at 1500 Volts RMS. The heat dissipation of the module under normal conditions is 6 Watts. The common mode rejection rating of the analog module is 60 dB and the common mode voltage is set at +/-170 Volts. The analog block has a 12-bit input resolution and the input update frequency takes place every 4 milliseconds.
The IC660BBA100 analog I/O block provides independent scaling for each input and output channel. The fault reporting to the host device can be easily enabled and disabled for an individual input or output. The selectable input filter time goes up to 1024 milliseconds. The IC660BBA100 analog I/O block has a thermal drift of 10 PPM at 25 degrees Celsius. The analog block’s outputs can be configured to hold the last state that they were in or to return to the default state if the CPU communication is lost. For wiring connections, the block uses 12 AWG wire. The block is backward compatible with older versions. It can be easily mounted using the screws on the back of the block.
Block Type: CatalogNumbers: 115 VACAnalogI / OBlock TerminalAssemblyonly ElectronicsAssemblyonly 24 / 48VDCAnalogI / OBlock TerminalAssemblyonly ElectronicsAssemblyonly |
4input / 2outputcircuits |
|
IC660BBA100 |
||
IC660TSA100 |
||
IC660EBA100 |
||
IC660BBA020 |
||
IC660TSA020 |
||
IC660EBA020 |
||
Size (height x width x depth): Weight: LEDs (block): Block to Block Isolation: HeatDissipation: |
8.83” (22.44cm) x 3.50” (8.89cm) x 3.94” (10.00cm) 4 lbs. (1.8 kg) UnitOK,I / OEnabled 1500 V 6 Watts |
|
Block Power(nominal): Operating range Maximumpower Frequency / ripple Power supply dropout time |
115 VAC 98–132 VAC 10 VA 47–63 Hz 1 cycle |
24/48 VDC 18–56 8W 10% max. ripple 10mS |
Common mode rejection: Commonmodevoltage: |
60 dB (0–1 KHz) " 170volts,maximum |
|
Absoluteaccuracy (at 25C): |
Typical: " 0.2% of full scale; Maximum: " 0.5% of full scale: within 50mV on the 10 volt range, 25mV on the 5 volt range, and 100mA on the 4 to 20 mA range. |
|
Thermaldrift (from 25C): |
Typical: 10 PPM per C; Maximum: 40 PPM per C |
|
Circuit range selections: |
0–10 VDC, " 10 VDC, " 5 VDC, 0–5 VDC, 4–20 mA (or 1–5 VDC) |
|
InputCharacteristics: Inputresolution Input update frequency Input filter ranges Inputdiagnostics |
12 bit + sign Once every 4mS none, 8, 16, 32, 64, 128, 256, 512, 1024mS Underrange, Overrange, High Alarm, Low Alarm, Open Wire |
|
OutputCharacteristics: Outputresolution Output update frequency Outputdiagnostics Output load |
12 bit + sign Once every 4mS Underrange, Overrange. Voltage mode: 2000ï— or greater; Current mode: 0 to 300ï— |
|
Environmental: Operatingtemperature Storagetemperature Humidity Vibration |
0 to 60C (+32 to 140F) –40 to +100C (–40 to +212F) 5% to 95% (non–condensing) 5–10 Hz 0.2” (5.08mm) displacement; 10–200 Hz at 1G |
Troubleshooting IC660BBA100
Troubleshooting information is available on IC660BBA100's website page; it also includes a datasheet, a user manual, and a wiring diagram.
Repair your IC660BBA100
PDF Supply can repair your IC660BBA100 in 3-5 business days. And PDF Supply stands by all of its repairs with a 1 year customer satisfaction warranty.
For more information on the IC660BBA100 Voltage/Current Analog I/O Block of the GE Fanuc Genius I/O Series, please see the Datasheet User-Manual.
IC660BBA100 is a Phase B GE Genius block and is compatible with all GENIUS supported PLC systems. The earlier version- IC660CBA100 is a Phase A GE Genius Block and is only compatible with Series Six and Series Five PLCs.
The final letter in the part number (ex. IC660BBA100K) indicates the revision. Revision K and later use the newer style electronic housing and therefore need the newer style plastic door and may indicate some compatibility issues with the terminal strip.
Common related search terms: Configuration, Datasheet, Emerson, Manual, PDF, PLC, Price, Specification, Troubleshoot, User-Manual, Wiring,
PDF Electric & Supply Inc. sells new, new surplus and refurbished products which are sourced through independent channels. All warranties and support, if applicable, are with PDF Electric & Supply Inc. and not the manufacturer. PDF Electric & Supply Inc. is not an authorized distributor or representative for the listed manufacturers and makes no representations as to any quality control performed by any listed manufacturer on the products. The products listed on this website may vary as to their country of origin; the accessories, and other items included with the product; and the language used on the packaging, the parts, and any related instructions or printed material related to the products. This website is not sanctioned or approved by any manufacturer or tradename listed. Designated trademarks, brand names and brands appearing herein are the property of their respective owners.