GE / IP FANUC Series 90/30 In Stock
Manufacturer | GE Fanuc |
---|---|
Series | Series 90-30 |
Part Number | IC660BBA104 |
Product Type | I/O Block |
Number of I/O Points | 6 |
Number of Inputs | 4 |
Number of Outputs | 2 |
Dimensions | 8.8 x 3.4 x 3.9 Inches |
Weight | 4 Pounds |
Voltage Type | AC and DC |
Nominal Voltage Rating | 115 Volts AC, 125 Volts DC |
Input Voltage Range | 98 to 132 Volts AC, 105 to 145 Volts DC |
Power Dissipation | 12 Watts |
Group-to-Group Isolation | 1500 Volts AC (RMS) |
The IC660BBA104 is a Genius Analog I/O Block of GE Fanuc series 90-30 PLCs. It belongs to the Analog Mixed Modules group and can be powered with either 115 VAC or 125 VDC. It has four inputs and two outputs whose I/O range is between 4 mA to 20 mA and provides the system with different types of diagnostics. Circuits are isolated, and accuracy of input is as precise as 0.1%.
Power is provided to the block and all the circuits from a single input, so that external power is not needed to process signals. After the signal enters the block, circuits apply linear scaling to convert it to engineering units. With every scan, 8 bytes of data containing those engineering data are broadcasted. The output data broadcast in 4 bytes. The block provides an output that connects to a Bus Switching Module (IC660BSM21) and is compatible with Genius Bus Controllers, PCIM and QBIM modules. To configure the IC660BBA104 Genius Analog I/O Block, the user needs a Hand-held monitor version 3.7 or later. The programming software is Logicmaster 6 ver. 4.02 or later. CPUs that are compatible with the block are rev. 105 or later for Series Six PLCs and rev. 3.0 or later for series 5 PLCs.
The block can be configured to detect input alarms, hold the last output state, or a default state and receive output feedback. The time to convert a signal to a value can be up to 400ms, and the block can work if there is CPU redundancy. Diagnostic checks involve detection of input open wire, input high and low alarms for each input individually, I/O over range and under range signal detection, and errors in output feedback.
Rated Voltage: | 115 VAC/ 125 VDC |
# of Points: | 4 Inputs / 2 Outputs |
Input Range: | 4 mA to 20 mA |
Output Range: | 4 mA to 20 mA |
Operating Voltage: | 93-132 VAC / 105-145 VDC |
Points per Common: | One group of 4 Inputs and one group of 2 Outputs |
The GE Fanuc IC660BBA104 input and output block is a GE Series 90-30 I/O block that comes with a total of 6 I/O points. Four of the I/O points on the IC660BBA104 I/O block are input points and the other 2 I/O points are output points. This I/O block is a current source I/O block that can be used as an interface between a GE Series 90-30 programmable logic controller (PLC) and field devices that can send and receive analog signals with a current range between 4 and 20 milliamps. The inputs and outputs on the IC660BBA104 I/O block are isolated from each other. This block can use AC or DC voltage, its nominal voltage ratings are 115 Volts AC and 125 Volts DC, and its supported operating voltage ranges are 93 to 132 Volts AC and 105 to 145 Volts DC.
The GE Fanuc IC660BBA104 I/O block from GE Series 90-30 has an input accuracy rating of 0.1% of the full scale rating, and an output accuracy rating of 0.15% of the full scale rating. It features block to block isolation as well as group to group isolation. The IC660BBA104 I/O block’s block to block isolation rating is 1500 Volts, and its group to group isolation rating is 1500 Volts RMS. The input resolution rating of the IC660BBA104 I/O block is 1 microamp while the output resolution rating is 6 microamps. The block’s dimensions are 8.8 x 3.4 x 3.9 inches and it weighs 4 pounds.
Block Type: CatalogNumbers: 115 VAC / 125VDCCurrent Source Analog block TerminalAssemblyOnly ElectronicsAssemblyOnly 24 / 48VDCCurrent Source Analog block TerminalAssemblyOnly ElectronicsAssemblyOnly |
Four input / 2 outputcircuits IC660BBA104 IC660TBA104 IC660EBA104 IC660BBA024 IC660TBA024 IC660EBA024 |
Size (height x width x depth) Weight: LED’s (I/O Block): HeatDissipation: BSMControl: |
8.83” (22.44cm) x 3.50” (8.89cm) x 3.94” (10.00cm) 4 lbs. (1.8 kg) UnitOK,I / OEnabled 12 Wattsmaximum Switches one 24 / 48 VDC BSM (IC660BSM021) |
Block to Block Isolation: Group to GroupIsolation: |
1500 V for one minute 300 V rms |
115VAC/125 VDCblockpower: Powersupplyvoltage Maximumcurrent Frequency / ripple Power supply dropout time |
115 VAC 125 VDC V VDC 250mA 140mA 47–63 Hz 10% max. ripple 1 cycle 10 mS min. |
24/48 VDCblockpower: Powersupplyvoltage Maximumcurrent Ripple Power supply dropout time |
18–56 VDC 600mA 10% max. 10 mS min. |
InputSignalCharacteristics: Input accuracy (at 25 C) Inputresolution Inputconversion time Range Overrangecapacity Inputdiagnostics Channel to channel isolation Thermal drift (from 25 C) |
0.1% of full scale reading 1ïA 16.6mS to 400mS (user selectable) 4mA to 20mA 0mA to 25mA Underrange, Overrange, High Alarm, Low Alarm, Open Wire 300 volts RMS 70 PPM per degree C typical |
InputImpedance: |
100 ohms $ 5% |
Normal Mode Rejection: |
–45 dB at 50, 60 Hz |
Input ExcitationCharacteristics: Open circuit voltage Short circuit current Loopimpedance |
24 VDC < 75mA 1000 ohms max. (0mA to 20mA)800 ohms max. (20mA to 25mA) |
OutputSignalCharacteristics: Output accuracy at 25 C Outputresolution Output update frequency Range Overrangecapacity Outputdiagnostics: Load: Thermaldrift (from 25C): |
0.15% of full scale reading 6ïA 6mS to 8mS typical 4mA to 20mA 0mA to 24mA Underrange, Overrange, Feedback error 0 ohms to 850 ohms 35 PPM per degreeC typical |
Environmental: Operating Temperature Storage Temperature Humidity Vibration |
0C to +60C (+32F to +140F) –40C to +100C (–40F to +212F) 5% to 95% (non–condensing) 5 – 10 Hz 0.2” (5.08mm) displacement, 10–200 Hz at 1G |
Troubleshooting IC660BBA104
Troubleshooting information is available on IC660BBA104's website page; it also includes a datasheet, a user manual, and a wiring diagram.
Repair your IC660BBA104
PDF Supply can repair your IC660BBA104 in 3-5 business days. And PDF Supply stands by all of its repairs with a 1 year customer satisfaction warranty.
For more information on the IC660BBA104 Current-Source Analog Output Block of the GE Fanuc Genius I/O Series, please see the Datasheet User-Manual.
The final letter in the part number (ex. IC660BBA104K) indicates the revision. Revision K and later use the newer style electronic housing and therefore need the newer style plastic door and may indicate some compatibility issues with the terminal strip.
Common related search terms: Configuration, Datasheet, Emerson, Manual, PDF, PLC, Price, Repair, Specification, Troubleshoot, User-Manual, Wiring,
PDF Electric & Supply Inc. sells new, new surplus and refurbished products which are sourced through independent channels. All warranties and support, if applicable, are with PDF Electric & Supply Inc. and not the manufacturer. PDF Electric & Supply Inc. is not an authorized distributor or representative for the listed manufacturers and makes no representations as to any quality control performed by any listed manufacturer on the products. The products listed on this website may vary as to their country of origin; the accessories, and other items included with the product; and the language used on the packaging, the parts, and any related instructions or printed material related to the products. This website is not sanctioned or approved by any manufacturer or tradename listed. Designated trademarks, brand names and brands appearing herein are the property of their respective owners.