GE / IP FANUC Series 90/30 In Stock
Preowned
PDF Supply Company, LLC is not an authorized distributor for GE Fanuc Emerson
Other Available Revisions for the IC660BBD022 IC660BBD022AIC660BBD022BIC660BBD022CIC660BBD022-CAIC660BBD022DIC660BBD022EIC660BBD022FIC660BBD022HIC660BBD022KIC660BBD022LIC660BBD022MIC660BBD022NIC660BBD022PIC660BBD022QIC660BBD022RIC660BBD022-RRIC660BBD022SIC660BBD022TIC660BBD022UIC660BBD022VIC660BBD022WIC660BBD022XIC660BBD022Y
Manufacturer | GE Fanuc |
---|---|
Series | Genius I/O |
Part Number | IC660BBD022 |
Product Type | I/O Block |
Circuits | 16 |
Load Current | 2 Amps |
Dimensions | 8.83 x 4.42 x 3.56 inches |
Heat Dissipation | 68.8 Watts with 2 Amps |
Maximum Ripple | 10 percent |
Operating Temperature | 32 to 140 degrees Fahrenheit |
The IC660BBD022 is a 24 VDC Source I/O, 16 Circuit, 2/3 Wire Sensor Compatible Block of GE Fanuc series 90-30 PLCs. It is among the discrete and analog blocks that belong to this series. It works with 24 VDC and is used with two and three wire solid state sensors and electromechanical sensors. Each of the 16 circuits, the block can work as an input, output, or tristate input, and no other components are required for configuration. Power supply is provided to all circuits by the block.
The IC660BBD022 has various configurable features. Among these are output test capability, selectable input time filter, output power up defaults, and output hold last state or default. The block has the ability to protect the system in case of electronic short circuit and over temperature. It can detect a failed switch, no load, and open wire in tristate inputs. In case there is overload, it detects the problem and shuts down.
This block can replace all its previous versions when a compatible electronics assembly is connected. The block should be installed in a protective case in a location with no airborne contaminants alongside adequate cooling and air flow.
IC660BBD022 needs a reliable grounding system. Terminals of this block interface with #12 wire or two #14 wires. There are 22 terminals on this block. The serial bus connects 1 to 4, and terminals 6 to 21 can be used as inputs or outputs by selecting the DC+ or DC- side of the terminal. DC power connects to terminals 5 and 22. When replacing an electronics assembly, the user must be careful because there is danger of electrical shock.
Rated Voltage: | 24 VDC |
# of Points: | 16 |
Input Range: | 18-30 VDC |
Load Current: | 2 Amp |
Operating Voltage: | 18-30 VDC |
Points per Common: | One group of 16 |
Block Type: CatalogNumbers: 24 / 48VDC16CircuitSourceI / OBlock Terminal Assemblyonly ElectronicsAssemblyonly 24VDC Source 16 Circuit Source I / O Block Terminal Assemblyonly ElectronicsAssemblyonly 24 / 48VDC16CircuitSinkI / OBlock Terminal Assemblyonly ElectronicsAssemblyonly 24VDC 16 Circuit Sink I / OBlock Terminal Assemblyonly ElectronicsAssemblyonly |
16 circuit discrete input and output |
IC660BBD020 |
|
IC660TSD020 |
|
IC660EBD020 (same as block IC660BBD022) |
|
IC660BBD022 |
|
IC660TBD022 |
|
IC660EBD020 (same as block IC660BBS020) |
|
IC660BBD021 |
|
IC660TSD021 |
|
IC660EBD021 (same as block IC660BBD023) |
|
IC660BBD023 |
|
IC660TBD023 |
|
IC660EBD021 (same as block IC660BBD021) |
|
Size (height x width x depth): |
8.83” (22.44cm) x 3.50” (8.89cm) x 3.94” (10.00cm) |
Weight: |
4 lbs. (1.8 kg) |
LEDS (block): |
Unit OK, I / OEnabled |
LEDs (each circuit): |
Individual load side indicators |
HeatDissipation: |
68.8 Watts with 16 outputs on at 2 amps. |
Block to Block Isolation: |
1500 V |
Operatingvoltage: |
18–56 VDC (24 / 48 V), 18–30 VDC (24 V) |
Ripple (maximum): |
10% |
Required DC power: |
150mAtypical / 300mAmaximum |
Power supply dropout time: |
10mS |
Input Characteristics: For standard input, voltage relative to (DC–) Input ON, 24 VDC supply 48 VDC supply* Input OFF, 24 VDC supply 48 VDC supply* Input processing time (typical) Input impedance (typical) Selectable input filter times Inputdiagnostics |
Source Blocks Sink Blocks |
16–24 VDC 0–8 VDC |
|
32–48 VDC * 0–16 VDC* |
|
0–7 VDC 17–24 VDC |
|
0–14 VDC* 34–48 VDC* |
|
5.6Kohms (24 / 48V), 1.8Kohms (24V) |
|
1.7mS (plus selectable filter delay) |
|
5–100mS |
|
Open wire, Overtemperature, Failed Switch |
|
OutputCharacteristics: Output current (steady state) |
2 amps per circuit |
Maximum inrush current |
10 amps up to 10mS |
Block output current |
15 amps at 35C |
Output OFF leakage current |
1.0 mA |
Maximumswitching frequency |
Once per second (high inrush current) |
Output turn–on delay (maximum) |
1mS |
Output voltage drop |
2.0 volts maximum at 2 amps inrush |
Minimum Recommended Load |
50 mA with No Load nabled |
Output Diagnostics |
Short Circuit, Overload, No Load, Failed Switch, Overtemperature |
Environmental: Operating temperature |
0 to +60C (32 to +140F) |
Storage temperature |
–40 to +100C (–40 to +212F) |
Humidity |
5 to 95% (non–condensing) |
Vibration |
5–10Hz 0.2” (5.08mm) displacement, 10–200Hz at 1G |
Troubleshooting IC660BBD022
Troubleshooting information is available on IC660BBD022's website page; it also includes a datasheet, a user manual, and a wiring diagram.
Repair your IC660BBD022
PDF Supply can repair your IC660BBD022 in 3-5 business days. And PDF Supply stands by all of its repairs with a 1 year customer satisfaction warranty.
For more information on the IC660BBD022 Current-Source Analog Output Block of the GE Fanuc Genius I/O Series, please see the Datasheet User-Manual.
The final letter in the part number (ex. IC660BBD022K) indicates the revision. Revision K and later use the newer style electronic housing and therefore need the newer style plastic door and may indicate some compatibility issues with the terminal strip.
Common related search terms: ConfigurationDatasheet, Emerson, Manual, PDF, PLC, Price, Repair, Specification, Troubleshoot, User-Manual, Wiring,
PDF Supply Company, LLC. sells surplus and refurbished products, which are sourced through independent channels. All warranties and support, if applicable, are with PDF Supply Company, LLC. and not the manufacturer; manufacturer warranties do not apply. PDF Supply Company, LLC. is not an authorized distributor or representative for the listed manufacturers and makes no representations as to any quality control performed by any listed manufacturers on the products. The products listed on this website may vary as to their country of origin; the accessories, and other items included with the product; and the language used on the packaging, the parts, and any related instructions or printed material related to the products. PDF Supply Company, LLC. does not sell or license software that may be needed to operate certain hardware and customers must obtain any necessary software licensing, maintenance, or upgrades from the manufacturer or other authorized source. This website is not sanctioned or approved by any manufacturer or other authorized source. This website is not sanctioned or approved by any manufacturer or tradename listed. Designated trademarks, brand names and brands appearing herein are the property of their respective owners.