GE / IP FANUC Series 90/30 In Stock
Preowned
PDF Supply Company, LLC is not an authorized distributor for GE Fanuc Emerson
Other Available Revisions for the IC660BBD024 IC660BBD024AIC660BBD024BIC660BBD024CIC660BBD024-CAIC660BBD024DIC660BBD024EIC660BBD024FIC660BBD024HIC660BBD024KIC660BBD024LIC660BBD024MIC660BBD024NIC660BBD024PIC660BBD024QIC660BBD024RIC660BBD024-RRIC660BBD024SIC660BBD024TIC660BBD024UIC660BBD024VIC660BBD024WIC660BBD024XIC660BBD024-X1
Manufacturer | GE Fanuc |
---|---|
Series | Genius I/O |
Part Number | IC660BBD024 |
Product Type | I/O Block |
Number of Channels | 32 |
Output Types | Standard and Feedback Outputs |
2-Wire Configuration | Supported |
3-Wire Configuration | Supported |
Calibration | Factory Calibration |
Voltage Type | DC |
The IC660BBD024 is a 12/24 VDC 32-Circuit Source I/O Block that sends current to field output devices. This block is an intelligent, configurable module that interfaces the controller to devices that send or receive a binary signal. The IC660BBD024 works with electronic proximity switches in 2-wire and 3-wire configurations, as well as a number of other input devices.
The IC660BBD024 block’s 32 identical discrete circuits can be set as input, output, or output with feedback. Block circuits are self-protecting. When a circuit is used as an output, block software protects its driver and guards against shorted electrical loads caused by wiring errors. In the interest of block operation, circuit protection also allows for short-duration surges.
Like other products in this class of electronics, block configuration is done with a handheld monitor. If a handheld monitor is not available, the user may choose to configure the block by sending a Write Configuration datagram from the host to the block. Block calibration is not necessary as it is performed by the manufacturer. Configuration, however, is performed by the user.
Genius I/O Source Blocks, including the IC660BBD024, provide current to field output devices but can function as a Bus Switching Module (BSM) controller. If needed, the user can replace the electronics assembly in this block without reconfiguring the block or removing field wiring if the replacement assembly is from a compatible block model. Like other blocks in the Genius I/O family, the IC660BBD024 should be installed within a protective enclosure. It can be mounted right-side up or upside down.
Rated Voltage: | 12/24 VDC |
# of Points: | 32 |
Input Range: | 18-30 VDC |
Load Current: | 0.5 |
Operating Voltage: | 10-30 VDC |
Points per Common: | One group of 32 |
The GE Fanuc IC660BBD024 I/O block is part of the GE Fanuc Genius I/O product line and it comes with 32 I/O channels. The IC660BBD024 I/O block is a current source type of I/O block. It is compatible with GE Series 90-30 and GE Series 90-70 PLCs as well as with GE Genius I/O PLCs. The Series 90-30, Series 90-70, and Genius I/O PLCs that use the IC660BBD024 I/O block can use it to interface with field devices that send and receive binary signals. This I/O block can be set up with a 2-wire configuration or a 3-wire configuration, and it can be configured with a handheld monitor.
All 32 of the I/O channels on the GE Fanuc Genius I/O IC660BBD024 I/O block can be configured by the users as inputs, as standard outputs, or as outputs with feedback. Additionally, all 32 of the I/O channels are equipped to protect themselves. They all have surge protection for power surges that only last for a short time, and the outputs have block software that protects them from electrical shorts and wiring errors. Although the users must configure the IC660BBD024 I/O block themselves so that it can handle their specific applications, they do not need to calibrate the I/O block because it was calibrated at the factory. It should be mounted inside an enclosure for protection from moisture and dust and it can be mounted either facing up or facing down depending on the system and application.
Block Type: CatalogNumbers: 32 Circuit 12 / 24 VDC Source: I / OBlock TerminalAssembly ElectronicsAssembly 32Circuit5 / 12 / 24VDCTTLSink: I / OBlock TerminalAssembly ElectronicsAssembly |
DC 32-circuit discrete input and output IC660BBD024 IC660TBD024 IC660EBD024 IC660BBD025 IC660TBD025 IC660EBD025 |
Size (height x width x depth): Weight LEDs (I/O Block) LEDs (each circuit) Block to Block Isolation HeatDissipation |
8.83” (22.44cm) x 3.56” (9.05cm) x 4.42” (11.23cm) 4 lbs. (1.8 kg) Unit OK, I / OEnabled Individual logic side indicators 850V
11W minimum with 8 inputs 18W maximum with 32 outputs at .5 amp |
Operating voltage (single source)
Ripple(maximum) Required DC power Power supply dropout times |
10 to 30 VDC (12 / 24 V supply) 4.9 to 5.3 VDC (5 V supply) (sink model only) absolute instantaneous limit 10% (12 / 24 volts) , 1% (5 volts) 150 mA typical, 300 mA maximum 4 mS at 12 volts, 20 ms at 24 volts |
Input Characteristics: Input voltage relative to (DC–) Input ON, 5 VDC supply 12 VDC supply 24 VDC supply Input OFF 5 VDC supply 12 VDC supply 24 VDC supply Input impedance (typical) Input processing time (typical) Selectable input filter times |
Source Blocks SinkBlocks not applicable 0–0.8 VDC 8–12 VDC 0–4 VDC 18–24 VDC 0–6 VDC not applicable 2–5 VDC 0–6 VDC 6–12 VDC 0–12 VDC 12–24 VDC 3.3 K ohms 1.4 mS (plus selectable filter delay) 1, 2, 3, 4, 5, 10, 20, 30, 40, 50, 60, 70, 80, 90, or 100mS |
OutputCharacteristics: Maximum output current (steady state) Maximum inrush current Block output current (total) Output OFF leakage current (maximum) Output turn–on delay (maximum) Output voltage drop Output Diagnostics |
0.5 amps per circuit 4 amps up to 10 mS (once every .5 sec. maximum) 16 amps 10ïA 0.5 mS 2.0 volts maximum at 4 amps inrush Switch Fault |
Environmental: Operating temperature Storage temperature Humidity Vibration |
0 C to +60 C (+32 to +140 F) –40 to +100 C (–40 to +212 F) 5% to 95% (non–condensing) 5–10Hz 0.2” (5.08mm) displacement, 10–200Hz at 1G |
Troubleshooting IC660BBD024
Troubleshooting information is available on IC660BBD024's website page; it also includes a datasheet, a user manual, and a wiring diagram.
Repair your IC660BBD024
PDF Supply can repair your IC660BBD024 in 3-5 business days. And PDF Supply stands by all of its repairs with a 2 year customer satisfaction warranty.
For more information on the IC660BBD024 Current-Source I/O Block of the GE Fanuc Genius I/O Series, please see the Datasheet User-Manual
The final letter in the part number (ex. IC660BBD024K) indicates the revision. Revision K and later use the newer style electronic housing and therefore need the newer style plastic door and may indicate some compatibility issues with the terminal strip.
Common related search terms: ConfigurationDatasheet, Emerson, Manual, PDF, PLC, Price, Repair, Specification, Troubleshoot, User-Manual, Wiring,
PDF Supply Company, LLC. sells surplus and refurbished products, which are sourced through independent channels. All warranties and support, if applicable, are with PDF Supply Company, LLC. and not the manufacturer; manufacturer warranties do not apply. PDF Supply Company, LLC. is not an authorized distributor or representative for the listed manufacturers and makes no representations as to any quality control performed by any listed manufacturers on the products. The products listed on this website may vary as to their country of origin; the accessories, and other items included with the product; and the language used on the packaging, the parts, and any related instructions or printed material related to the products. PDF Supply Company, LLC. does not sell or license software that may be needed to operate certain hardware and customers must obtain any necessary software licensing, maintenance, or upgrades from the manufacturer or other authorized source. This website is not sanctioned or approved by any manufacturer or other authorized source. This website is not sanctioned or approved by any manufacturer or tradename listed. Designated trademarks, brand names and brands appearing herein are the property of their respective owners.