GE / IP FANUC Series 90/30 In Stock
Other Available Revisions for the IC660BBD025 IC660BBD025/AIC660BBD025/BIC660BBD025/CIC660BBD025/CAIC660BBD025/DIC660BBD025/EIC660BBD025/FIC660BBD025/HIC660BBD025/KIC660BBD025/LIC660BBD025/MIC660BBD025/NIC660BBD025/PIC660BBD025/QIC660BBD025/RIC660BBD025/RRIC660BBD025/SIC660BBD025/TIC660BBD025/UIC660BBD025/VIC660BBD025/WIC660BBD025/W1
Manufacturer | GE Fanuc |
---|---|
Series | Genius I/O |
Part Number | IC660BBD025 |
Product Type | Sink I/O Block |
Number of I/O | 32 |
Block to Block Isolation | Supported |
Voltage Type | DC |
Nominal Voltage | 5, 12, 24 Volts DC |
Isolation Voltage | 850 Volts |
Operating Voltage | 4.9 to 5.3 Volts DC, 10 to 30 Volts DC |
The IC660BBD025 is a 5/12/24 VDC 32-Circuit Sink I/O Block. This block is an intelligent, configurable module that interfaces the controller to devices that send or receive binary signals. IC660BBD025 works with both 2-wire and 3-wire proximity switches, as well as other input devices. It is important to note that if the user plans to provide current to field output devices rather than receive current, a Source Block IC660BBD024 is recommended.
Source and Sink block versions each operate with direct current (12 to 24 volts). IC660BBD025 is also +5 volt TTL (transistor-transistor logic) compatible. The block’s 32 circuits can be configured as input, output, or output with feedback. In output configurations, block architecture protects driver circuits against short circuits caused by wiring errors. Configurable features of the IC660BBD025 include Output Pulse Test capability, Input Filter Time, CPU Redundancy type, Output Hold behavior, and its readiness for use as a Bus Switching Module control.
Block terminals 5 through 46 are for connecting field devices. The user should wire the block power disconnects so that block power and input power can be removed at the same time. Simultaneous power removal ensures that the block will not power up unexpectedly when multiple inputs are activated.
IC660BBD025 ships with block diagnostics that monitor output and check actual switch state against expected or commanded switch state. The block handles a steady-state load of 0.5 Amps when operating normally. Block behavior and circuits are configured using a handheld monitor. The monitor can also be used with LEDs on the chassis of the block itself to check operating status at a glance.
When installing the block, it is crucial to use a protective case and choose a place with no airborne contaminants. Adequate cooling and air flow are essential. Ground screws must connect to a reliable grounding system. To properly disconnect block power, circuit power must be disconnected.
Rated Voltage: | 5/12/24 VDC |
# of Points: | 32 |
Input Range: | 4.9-5.3 VDC or 10-30 VDC |
Load Current: | 0.5 |
Operating Voltage: | 4.9-5.3 VDC or 10-30 VDC |
Points per Common: | One group of 32 |
The GE Fanuc IC660BBD025 I/O block is a sink I/O block from the Genius I/O series. It is compatible with devices from both the GE Fanuc Genius I/O line and the Series 90-30 line. It comes with 32 I/O points and it supports block to block isolation. The nominal voltage ratings that the IC660BBD025 sink I/O block can support are 5 Volts DC, 12 Volts DC, and 24 Volts DC. The block to block isolation voltage rating is 850 Volts. The IC660BBD025 sink I/O block dissipates about 11 Watts of energy as heat when 8 of its I/O points are operating as inputs, and it dissipates about 18 Watts of energy as heat when all 32 of its I/O points are operating as inputs.
The GE Fanuc Genius I/O IC660BBD025 sink I/O block comes with multiple ports in addition to all of its I/O points. These ports are the monitoring port, Serial Port 1, Serial Port 2, the shield in port, and the shield out port. It should be grounded with grounding screws and installed in an enclosure that will protect it from debris and moisture while also allowing it to have enough airflow for air-cooling. The IC660BBD025 sink I/O block operates with DC voltage and it supports operating voltage ranges of 4.9 to 5.3 Volts DC or 10 to 30 Volts DC. The Genius I/O IC660BBD025 sink I/O block is designed to be compact with dimensions of 8.8 x 3.6 x 4.7 inches.
Block Type: CatalogNumbers: 32 Circuit 12 / 24 VDC Source: I / OBlock TerminalAssembly ElectronicsAssembly 32Circuit5 / 12 / 24VDCTTLSink: I / OBlock TerminalAssembly ElectronicsAssembly |
DC 32-circuit discrete input and output IC660BBD024 IC660TBD024 IC660EBD024 IC660BBD025 IC660TBD025 IC660EBD025 |
Size (height x width x depth): Weight LEDs (I/O Block) LEDs (each circuit) Block to Block Isolation HeatDissipation |
8.83” (22.44cm) x 3.56” (9.05cm) x 4.42” (11.23cm) 4 lbs. (1.8 kg) Unit OK, I / OEnabled Individual logic side indicators 850V
11W minimum with 8 inputs 18W maximum with 32 outputs at .5 amp |
Operating voltage (single source)
Ripple(maximum) Required DC power Power supply dropout times |
10 to 30 VDC (12 / 24 V supply) 4.9 to 5.3 VDC (5 V supply) (sink model only) absolute instantaneous limit 10% (12 / 24 volts) , 1% (5 volts) 150 mA typical, 300 mA maximum 4 mS at 12 volts, 20 ms at 24 volts |
Input Characteristics: Input voltage relative to (DC–) Input ON, 5 VDC supply 12 VDC supply 24 VDC supply Input OFF 5 VDC supply 12 VDC supply 24 VDC supply Input impedance (typical) Input processing time (typical) Selectable input filter times |
Source Blocks SinkBlocks not applicable 0–0.8 VDC 8–12 VDC 0–4 VDC 18–24 VDC 0–6 VDC not applicable 2–5 VDC 0–6 VDC 6–12 VDC 0–12 VDC 12–24 VDC 3.3 K ohms 1.4 mS (plus selectable filter delay) 1, 2, 3, 4, 5, 10, 20, 30, 40, 50, 60, 70, 80, 90, or 100mS |
OutputCharacteristics: Maximum output current (steady state) Maximum inrush current Block output current (total) Output OFF leakage current (maximum) Output turn–on delay (maximum) Output voltage drop Output Diagnostics |
0.5 amps per circuit 4 amps up to 10 mS (once every .5 sec. maximum) 16 amps 10ïA 0.5 mS 2.0 volts maximum at 4 amps inrush Switch Fault |
Environmental: Operating temperature Storage temperature Humidity Vibration |
0 C to +60 C (+32 to +140 F) –40 to +100 C (–40 to +212 F) 5% to 95% (non–condensing) 5–10Hz 0.2” (5.08mm) displacement, 10–200Hz at 1G |
Troubleshooting IC660BBD025
Troubleshooting information is available on IC660BBD025's website page; it also includes a datasheet, a user manual, and a wiring diagram.
Repair your IC660BBD025
PDF Supply can repair your IC660BBD025 in 3-5 business days. And PDF Supply stands by all of its repairs with a 1 year customer satisfaction warranty.
For more information on the IC660BBD025 Sink I/O Block of the GE Fanuc Genius I/O Series, please see the Datasheet User-Manual.
The final letter in the part number (ex. IC660BBD025K) indicates the revision. Revision K and later use the newer style electronic housing and therefore need the newer style plastic door and may indicate some compatibility issues with the terminal strip.
Common related search terms: ConfigurationDatasheet, Emerson, Manual, PDF, PLC, Price, Repair, Specification, Troubleshoot, User-Manual, Wiring,
PDF Electric & Supply Inc. sells new, new surplus and refurbished products which are sourced through independent channels. All warranties and support, if applicable, are with PDF Electric & Supply Inc. and not the manufacturer. PDF Electric & Supply Inc. is not an authorized distributor or representative for the listed manufacturers and makes no representations as to any quality control performed by any listed manufacturer on the products. The products listed on this website may vary as to their country of origin; the accessories, and other items included with the product; and the language used on the packaging, the parts, and any related instructions or printed material related to the products. This website is not sanctioned or approved by any manufacturer or tradename listed. Designated trademarks, brand names and brands appearing herein are the property of their respective owners.