GE / IP FANUC Series 90/30 In Stock
PDF Supply Company, LLC is not an authorized distributor for GE Fanuc Emerson
Other Available Revisions for the IC660BBR101 IC660BBR101AIC660BBR101BIC660BBR101CIC660BBR101-CAIC660BBR101DIC660BBR101EIC660BBR101FIC660BBR101HIC660BBR101KIC660BBR101LIC660BBR101MIC660BBR101NIC660BBR101PIC660BBR101QIC660BBR101-Q1IC660BBR101-RR
|Product Type||Output Block|
|Number of Outputs||16|
|Output Voltage Type||AC or DC|
|Number of Output Groups||4|
|Frequency||47 to 63 Hertz|
|Operating Temperature||32 to 140 degrees Fahrenheit|
|Storage Temperature||-40 to 212 degrees Fahrenheit|
The IC660BBR101 is a Normally Open Relay Output Block manufactured by GE Fanuc. The block comes with 16 output circuits grouped into four groups, each with four outputs. Each output can be powered by either AC or DC. Because of its normally open design, the block’s contacts are separated by default until power is applied to close the gap existing between circuit components.
The relay block has a rated voltage of 115 VAC, which is the factory setting, to 230 VAC. The voltage selection is made possible by jumpers located on the block’s assembly. The block runs on a load current of 2 Amps. Output circuit group isolation is 1500VAC. IC660BBR101 is useful in a variety of low power applications such as relays, lamps, and contactors.
A handheld monitor is used for customization of the relay output. This includes setting up defaults for power-up output actions, reverting to factory settings if there is electrical communication interference, and selecting redundancy types. The block can alternatively be used as a bus switching module (BSM).
LEDs on the block display the status of the unit as well as input and output conditions. A blinking LED indicates a fault in the circuit. When the LED is OFF, the block is faulty and/or not drawing power. A simple LED ON indicates optimum performance. If a normally closed relay block is preferred, consider the IC660BBR100 relay output block.
|Rated Voltage:||115 VAC or 230 VAC|
|# of Points:||16|
|Load Current:||2 Amp|
|Operating Voltage:||93-132 VAC / 185-265 VAC|
|Points per Common:||Four groups of 4|
The GE Fanuc IC660BBR101 output block is a normally open output block from the GE Fanuc Genius I-O series. The IC660BBR101 output block has 16 outputs. These outputs are divided into 4 groups, and each output can be configured for operation with AC or DC voltage. This output block is known as a normally open output block because its contacts are normally open. It can be used in a CPU redundancy setup in a Genius I-O PLC. The relay that the IC660BBR101 output block uses is a fixed coil and moving armature type of relay. It is well-suited for machine control applications and for working with different types of low-power devices. It can tolerate an operating frequency in the range of 47 to 63 Hertz.
The GE Fanuc Genius I-O IC660BBR101 16-channel normally open output block is suitable for use in all standard, non-hazardous industrial environments. It can tolerate atmospheres with relative humidity levels between 5% and 95% in operation and in storage, as long as the humidity never condenses. The operating temperature range for the IC660BBR101 16-channel output block is between 0 degrees Celsius and 60 degrees Celsius or 32 degrees Fahrenheit and 140 degrees Fahrenheit. When it is not being used, this 16-channel normally open output block can tolerate an ambient temperature range between -40 degrees Celsius and 100 degrees Celsius or -40 degrees Fahrenheit and 212 degrees Fahrenheit. Devices that are compatible with the IC660BBR101 16-channel output block are devices with voltage ranges of 5 to 250 Volts AC or of 5 to 220 Volts DC.
Block Type: CatalogNumbers:
Output Block, Normally–Closed Relays TerminalAssemblyonly ElectronicsAssemblyonly
Output Block, Normally-Open Relays TerminalAssemblyonly
16 circuit relay outputs in four isolated groups of four
IC660BBR100 IC660TBR100 IC660EBR100 IC660BBR101 IC660TBR101
Size (height x width x depth):
LEDs (I/O Block)
LEDs (each circuit)
8.83” (22.44cm) x 3.50” (8.89cm) x 3.94” (10.00cm)
4 lbs. (1.8 kg)
UnitOK,I / OEnabled
Individual relay coilstate
EnvironmentalSpecifications: Operatingtemperature Storagetemperature Humidity
0C to +60C (32F to +140F)
–40C to +100C (–40F to +212F)
5 to 95% (non–condensing)
5–10Hz 0.2” (5.08mm) displacement; 10–200Hz at 1G
Block PowerSupply: Frequency Operatingvoltage
Power supplydropouttime Isolation:
Alloutputs to chassis ground Between output groups
Power terminals to chassis ground Power terminals to outputs
Comms terminals to power terminals Comms terminals to outputs
(115VAC) 93VAC to 132VAC; (230VAC) 185VAC to 265VAC 87mA at 115 VAC
10.1 watts maximum with 16 outputs on
OutputCharacteristics: Maximum Output current Maximumswitchingpower Maximuminrush current Output OFF leakage current
Maximumswitchingfrequency Output turn–on delay (maximum) Output voltage range
2 amps per circuit 60 Watts or 125 VA 2 amps per circuit
20cycles / minute(inductiveloads) 5mS
5V to 250V AC or 5V to 220V DC
Initial Contact Resistance
Fixed coil moving armature 100 milliohms, maximum
Typical Life: OperatingVoltage:
MaximumCurrent for Load Type * TypicalLife Resistive Lamp Solenoid (operations) 0.5A –– –– 200,000
–– 0.1A 0.1A 100,000
1.0A 0.2A 0.3A 100,000
0.3A –– –– 100,000
0.6A –– –– 100,000
2.0A –– –– 500,000
–– 0.2A 0.3A 100,000
–– 0.3A 0.5A 100,000
Effect of AdditionalCurrent onOperatingLife:
Current in Load Type TypicalLife Resistive Lamp Solenoid (operations) 0.1A –– –– 1,500,000
0.3A –– –– 1,000,000
1.0A –– –– 2,000,000
2.0A –– –– 1,000,000
* Lamp loads are defined as a X10 inrush with a power factor (PF) of 1.00; when turned OFF, they represent a PF of 1.00. Solenoids are de- fined as a X10 inrush with a PF of 0.65; when turned OFF, they repre-
sent a PF of 0.35.
Repair your IC660BBR101
For more information on the IC660BBR101 Relay Output Block of the GE Fanuc Genius I/O Series, please see the Datasheet User-Manual.
The final letter in the part number (ex. IC660BBR101K) indicates the revision. Revision K and later use the newer style electronic housing and therefore need the newer style plastic door and may indicate some compatibility issues with the terminal strip.
PDF Supply Company, LLC. sells surplus and refurbished products, which are sourced through independent channels. All warranties and support, if applicable, are with PDF Supply Company, LLC. and not the manufacturer; manufacturer warranties do not apply. PDF Supply Company, LLC. is not an authorized distributor or representative for the listed manufacturers and makes no representations as to any quality control performed by any listed manufacturers on the products. The products listed on this website may vary as to their country of origin; the accessories, and other items included with the product; and the language used on the packaging, the parts, and any related instructions or printed material related to the products. PDF Supply Company, LLC. does not sell or license software that may be needed to operate certain hardware and customers must obtain any necessary software licensing, maintenance, or upgrades from the manufacturer or other authorized source. This website is not sanctioned or approved by any manufacturer or other authorized source. This website is not sanctioned or approved by any manufacturer or tradename listed. Designated trademarks, brand names and brands appearing herein are the property of their respective owners.