GE / IP FANUC Series 90/30 In Stock
Other Available Revisions for the IC660BBS100 IC660BBS100/AIC660BBS100/BIC660BBS100/CIC660BBS100/CAIC660BBS100/DIC660BBS100/EIC660BBS100/FIC660BBS100/HIC660BBS100/RR
Manufacturer | GE Fanuc |
---|---|
Series | Genius I/O |
Part Number | IC660BBS100 |
Product Type | I/O Block |
Voltage Ratings | 115 Volts AC/125 Volts DC |
Block to Block Isolation | 1500 Volts |
Heat Dissipation | 16.8 Watts |
Fusing | Internal electronic short circuit trip |
Operating Temperature | 0 to 60 degrees Celsius |
Weight (approx.) | 4 Pounds |
**IC660BBS102 replaces IC660BBS100**
The IC660BBS100 is an isolated I/O Block manufactured by GE Fanuc that provides eight circuits in four isolated groups (each having two circuits). Its rated voltage is either 115 VAC or 125 VDC with a current of 2 Amps. The isolation is rated to withstand 250 VAC/VDC between any two groups.
Electronic fusing is built in for every circuit being used as an output. Should a short circuit occur, the circuit will shut down after five microseconds. However, the block can easily be restarted from the CPU or from a handheld monitor. Additional diagnostic checks performed by the block include unexpected shutdown, power overload, detection of load absence, and over temperature. An isolated block can be configured as input only, output only, or a combination of the two.
Each circuit comes with its own LED responsible for indicating threshold voltage for a circuit configured for input. For an output circuit, it indicates the mode configured by the CPU. Some of the configurable features of the IC660BBS100 block include bus switching control, presence of a dual power circuitry (i.e., both DC and AC circuitry), an input filter time that is easily selectable ranging from 10 ms to 100 ms, test capability of output pulse, and CPU redundancy type.
The block is 100% compatible with a hand-held monitor (models IC660HHM501 and IC660HHM500). IC660BBS100 is also compatible with any bus controller manufactured by GE Fanuc.
The IC660BBS100 Isolated I/O Block belongs to the GE Fanuc Genius I/O series of I/O modules. It comes with 4 isolated groups of 2 I/O circuits each for a total of 8 I/O. It is compatible with the IC660HHM501 hand-held monitor which can be used for the configuration of the block. This I/O block is backward compatible with the previous block versions. The IC660BBS100 Isolated I/O Block has an LED to indicate the operating status of each of its I/O circuits. Additionally, each circuit of the module has a built-in thermal sensor. The block’s diagnostic facilities are made to report all the faults of the module to the hand-held programmer so that the users can take the necessary corrective actions as quickly as possible.
The IC660BBS100 Isolated I/O Block has an I/O circuit which is rated to operate at a nominal voltage of 115 Volts AC or 125 Volts DC. It can perform a variety of diagnostic checks including no-load detection, over-temperature detection, open-wire detection for the tri state inputs, and overload detection, and it can shut down to protect itself. This isolated I/O block can act as an input-only, output-only, or combination block. Once it is configured as an input-only block, all the circuits act as regular inputs and tri-state inputs. The configurable features of the IC660BBS100 Block are its output pulse test capability, CPU redundancy, bus switching module control, and selectable input filter times. It also comes with an internal electronic short circuit trip for safety. The heat dissipation rating of the module is 18.8 Watts. Its dimensions are 8.83 x 3.5 x 3.94 inches and its approximate weight is 4 pounds. It is recommended to configure the module as a combination block to have a mix of inputs and outputs.
Block Type: 115VAC / 125VDCIsolatedI / OBlock: Terminal Assembly Only: ElectronicsAssemblyOnly: 115VAC / 125VDCIsolatedI / OBlock,NoFailed Switch: Terminal Assembly Only: ElectronicsAssemblyOnly: |
8 ckt isolated input / output in 4 isolated pairs IC660BBS102, replaces IC660BBS100 IC660TSS100 IC660EBS100 IC660BBS103, replaces IC660BBS101 IC660TSS100 IC660EBS101 |
Size (height x width x depth): Weight: LED’s (I/O Block): LED’s (each circuit): Block to Block Isolation: HeatDissipation: |
8.83” (22.44cm) x 3.50” (8.89cm) x 3.94” x (10.00cm) 4 lbs. (1.8 kg) Unit OK, I / OEnabled On logic side of switch 1500 V 16.8W max. with 8 inputs on, 45.6W max. with 8 outputs at 2 amps |
Operating Temperature Storage Temperature Humidity Vibration |
–0 to +60C (32 to +140F) –40 C (–40 to +212F) 5% to 95% (non–condensing) 5–10 Hz 0.2” (5.08mm) displacement, 10–200 Hz at 1G |
Required control power (block only): Operating voltage (four sources): Frequency/ripple: Power supply dropout time: |
8 Wattsmaximum |
93–132 VAC 105–132 VDC 47–63 Hz 10% max. ripple 1 cycle 10mS |
|
Input Characteristics: Non–tristate input, OFF state: Minimum voltage across input device (IN to H) Maximum leakage through input device Non–tristate input, ON state: Maximum voltage across input device (IN to H) Maximumswitchcurrent threshold Tristate input: OFF, acceptable voltage across input device (IN to H) ON, maximum voltage across input device (IN to H) Input load network: Resistor to N Capacitor to H: for blocks BBS100 and BBS101 Capacitor to H: for blocks BBS102 and BBS103 Input processing time (typical) Selectable input filter times Inputdiagnostics |
For AC For DC 60 VRMS 70 VDC 1 mA 2 mA 20 VRMS 35 VDC 6 mA RMS 5 mA 16 VRMS–40 VRMS 16 VDC–35 VDC 4 VRMS 3.5 VDC 13K ohms 13K ohms .22 ïf .22 ïf .1 ïf .1 ïf 2mS + filter 0.8mS + filter |
10 to 100mS in 10mS increments Open Wire, Overtemperature, Loss of I / O Power, Failed Switch |
|
OutputCharacteristics: Output current (steady state) Maximum inrush current Output Leakage: Current at 0 volt output: for blocks BBS102 and 103 Current at 0 volt output: for blocks BBS100 and 101 Voltage at open output: for blocks BBS102 and 103 Voltage at open output: for blocks BBS100 and 101 Output switch (OFF to ON / ON to OFF) Rated switching frequency at maximum inrush Turn–on delay (maximum) Voltage drop (at 2 amps) Voltage drop (at 20 amps inrush) Minimum load (No Load disabled) Resistive: for blocks BBS102 and BBS103 Resistive: for blocks BBS100 and BBS101 Inductive: for blocks BBS102 and BBS103 Inductive: for blocks BBS100 and BBS101 No Load enabled threshold Maximum block output current Fusing Output diagnostics |
For AC For DC 2 amps 2 amps resistive 9 (1 amp inductive*) 25 amps (2 cycles) 25 amps (10mS peak) 7 mA 2 mA 13mA 2 mA 65 volts 40 volts 95 volts 40 volts Zerocrossing ––– Once per second Once per second 0.5 Hz + 1mS 1mS 2.5 volts 2.5 volts 10 volts 10 volts 25 mA 10 mA 30 mA 10 mA 40 mA 10 mA 100mA 10 mA 50 mA 50 mA |
15 amps at 35 C, 7.5 amps at 60C Internal electronic short circuit trip. 100ms(AC), 10ms (DC) long time trip Short Circuit, Overload, No Load, Overtemp., Loss of I / O Power.Also, for blocks BBS100 and BBS 102 only: Failed Switch |
IC660BBS100 is a Phase B GE Genius block and is compatible with all GENIUS supported PLC systems. The earlier version- IC660CBS100 is a Phase A GE Genius Block and is only compatible with Series Six and Series Five PLCs.
The final letter in the part number (ex. IC660BBS100K) indicates the revision. Revision K or later use the newer style electronic housing and therefore needs the newer style plastic door and may indicate some compatibility issues with the terminal strip.
Common related search terms: ConfigurationDatasheet, Emerson, Manual, PDF, PLC, Price, Repair, Specification, Troubleshoot, User-Manual, Wiring,
PDF Electric & Supply Inc. sells new, new surplus and refurbished products which are sourced through independent channels. All warranties and support, if applicable, are with PDF Electric & Supply Inc. and not the manufacturer. PDF Electric & Supply Inc. is not an authorized distributor or representative for the listed manufacturers and makes no representations as to any quality control performed by any listed manufacturer on the products. The products listed on this website may vary as to their country of origin; the accessories, and other items included with the product; and the language used on the packaging, the parts, and any related instructions or printed material related to the products. This website is not sanctioned or approved by any manufacturer or tradename listed. Designated trademarks, brand names and brands appearing herein are the property of their respective owners.