GE / IP FANUC Series 90/30 In Stock

World's Largest Warehouse

of GE 90-30, Genius, and RX7i

Mon-Fri 8AM-5PM EST



Rated 4.9/5 Based on 10 ratings.

Rate your purchase of the IC660EBA100
IC660EBA100 In Stock! Electronic Assembly for IC660E IC660EB IC660EBA PDFsupply also repairs GE IP F

SKU 2174316  UPC 014120142083

All product names, trademarks, brands and logos used on this site are the property of their respective owners. PDF Supply is not an authorized distributor, reseller or representative of the products featured on this website. The depiction, description or sale of products featuring these names, trademarks, brands and logos is for identification purposes only and is not intended to in indicate any affiliation with or authorization by any rights holder.

PDF Supply is NOT an authorized distributor for this manufacturer and therefore the manufacturer’s warranty does not apply. Product comes with PDF Supply's 1-year, 2-year, or 3-year warranty.

Common misspellings:
  • 1C660EBA100
  • IC66oEBA100
  • IC660E8A100
  • IC660EBAl00
  • IC660EBA1o0
  • IC660EBA10o
  • IC660EBA100

The IC660EBA100 module is a GE Fanuc Input / Output module with 4 inputs and 2 outputs. It comes with 2 block versions. We have a 115 VAC input/output block and a 24/48 VDC voltage / current block. Each circuit on the 4 input / 2 Output Analog Block, can deliver signals in the following analog ranges:

-10V DC to +10V DC

-5V DC to +5V DC

0-5 V DC

0 -10 V DC

4-20 mA/1-5 volts DC

Due to this flexibility in the above signal ranges, the module blocks can be used in wide arrays of both output and input devices.

You’ll notice LED indicators on the block for indicating how the block is running. If a block develops a fault, the OK LED blinks to give a sign of an existing fault. For certain faults, the block takes preemptive measures by cutting off the module’s output to avert hazardous incidences that could lead to further damage. This input / output module is mountable in any position. For ample heat dissipation, vertical mounting is preferred.

It is recommended that about 1.5 inches are left open between the blocks and 3 inches above and below each block. This facilitates easier removal of the block’s electronics component and provides more space for wiring especially where wires are bundled together.

If mounted in an enclosed area, it’s crucial to leave adequate space for cooling. Remember, overheating is potentially harmful to electronic components. Connections to the I/O blocks are made using Belden 9182 cables. For configuration, a hand-held monitor is attached to the block and powered on.  This is followed by a series of configuration prompts. Finally, a device number is assigned to the I/O block to start configuration.

During field wiring, the I/O block is operated using a standard screwdriver for fastening and unfastening the screws. Each terminal can accommodate one AWG #12 or two AWG #14 wires. The minimum wire size that is recommended is AWG #22. Take note that unshielded wire ends do not exceed 2 inches.

 The final letter in the part number (ex. IC660EBA100K) indicates the revision. Revision K or later use the newer style electronic housing and therefore needs the newer style plastic door and may indicate some compatibility issues with the terminal strip.

ST. LOUIS, Feb. 1, 2019 – Emerson today announced it has completed the purchase of Intelligent Platforms from General Electric.

Common related search terms: Emerson


PDF Supply sells used surplus products. PDF Supply is not an authorized distributor, affiliate, or representative for the brands we carry. Products sold by PDF Supply come with PDF Supply’s 1-year, 2-year, or 3-year warranty and do not come with the original manufacturer’s warranty. Designated trademarks, brand names and brands appearing herein are the property of their respective owners. This website is not sanctioned or approved by any manufacturer or tradename listed.

Rockwell Disclaimer: The product is used surplus. PDF Supply is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because PDF Supply is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, PDF Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. PDF Supply also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. PDF Supply also makes no representations as to your right to install any such firmware on the product. PDF Supply will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.