GE / IP FANUC Series 90/30 In Stock
PDF Supply Company, LLC is not an authorized distributor for GE Fanuc Emerson
Other Available Revisions for the IC660TBR101 IC660TBR101AIC660TBR101BIC660TBR101CIC660TBR101-CAIC660TBR101DIC660TBR101EIC660TBR101FIC660TBR101HIC660TBR101KIC660TBR101LIC660TBR101MIC660TBR101NIC660TBR101PIC660TBR101QIC660TBR101-Q1IC660TBR101-RR
|Product Description||Terminal Assembly|
|Voltage Rating||115/230 Volts AC|
|Compatible I/O Block||IC660BBR101|
|Compatible Electronic Assembly||IC660EBR101|
|Operating Temperature||0 to 60 degrees Celsius|
|Storage Temperature||-40 to 100 degrees Celsius|
|Relative Humidity||5%-95%, Non-condensing|
GENIUS Terminal Assembly for (TBR Only) TBR101 for IC660BBR101 IC660T IC660TB IC660TBR
The IC660TBR101 Terminal Assembly is a Genius I/O series product that is designed for use with the IC660BBR101 Relay Output Block. It comes with 115/230 Volts AC voltage, a box-style design, IC660BBR101 relay output block compatibility, and it weighs 2 pounds. Some of the main features of this module include configuration flexibility, reduced installation costs, circuit protection, and advanced diagnostics. All the field wiring of the relay output module is done through this terminal assembly. Even though the IC660TBR101 Terminal Assembly is permanently installed with the block once they are attached, its electronics assembly can be removed without changing the field wiring.
The IC660TBR101 Terminal Assembly is compatible with the IC660EBR101 Electronics Assembly. It has 32 screw-type terminals. The terminals use AWG #22 to AWG #12 wires for the field wiring. It can provide the required power to the relay output block by using a 115 Volts AC or 230 Volts AC power source. The power source voltage is jumper-selectable. However, additional care must be taken when using the jumper to avoid damages to the block. The operating temperature range of the IC660TBR101 Terminal Assembly is 0 to 60 degrees Celsius. Since the relay output block does not have internal fuses, external 2-Amp fuses can be installed to protect the load. Terminals 5 to 32 are reserved for field device connections. Terminals 3 and 4 are labeled as Shield 1 and Shield 2, respectively. The shield out terminal is directly connected to the chassis ground. This terminal assembly module makes field wiring easy.
The IC660TBR101 block is a GE terminal block. This block is one of the main components of a complete I/O block. The block comes with 16 circuit relay outputs that are placed in groups of 4. All 4 of the circuits share a common input terminal. The terminal block is 8.83 inches in height, 3.50 inches in width, and 3.94 inches in depth. It is lightweight and weighs only 4 pounds. This terminal assembly is used with an open relay output block with an open architecture. The assembly can be mounted both vertically and horizontally depending on the installation area. The top section on the front side has a port to connect hand held monitor and programming terminals.
The IC660TBR101 terminal block has a current rating of 87 milliamps with a voltage of 115/230 Volts AC. For installation, the environmental temperature should be set between 0 and 60 degrees Celsius and the assembly can be stored at a temperature between -40 and 100 degrees Celsius. The IC660TBR101 terminal block has LED indicators for individual circuits that show the flow of power through them. There is also the “Unit OK” LED. The operating frequency of the terminal is 50/60 Hertz. The drop out time of the power supply is 1 cycle and it has an isolation rating of 1500 Volts AC for output to chassis. The assembly dissipates 10.1 Watts of energy as heat with all 16 outputs turned on. The IC660TBR101 terminal block should work with a minimum load of 10 milliamps with an output off-state leakage current of 0.1 Amps.
The final letter in the part number (ex. IC660TBR101K) indicates the revision. Revision K or later use the newer style electronic housing and therefore needs the newer style plastic door and may indicate some compatibility issues with the terminal strip.
PDF Supply Company, LLC. sells surplus and refurbished products, which are sourced through independent channels. All warranties and support, if applicable, are with PDF Supply Company, LLC. and not the manufacturer; manufacturer warranties do not apply. PDF Supply Company, LLC. is not an authorized distributor or representative for the listed manufacturers and makes no representations as to any quality control performed by any listed manufacturers on the products. The products listed on this website may vary as to their country of origin; the accessories, and other items included with the product; and the language used on the packaging, the parts, and any related instructions or printed material related to the products. PDF Supply Company, LLC. does not sell or license software that may be needed to operate certain hardware and customers must obtain any necessary software licensing, maintenance, or upgrades from the manufacturer or other authorized source. This website is not sanctioned or approved by any manufacturer or other authorized source. This website is not sanctioned or approved by any manufacturer or tradename listed. Designated trademarks, brand names and brands appearing herein are the property of their respective owners.