PDF Electric and Supply

1-800-360-6802
1-919-535-3180
sales@pdfsupply.com

IC694DSM324

Buy NowIC694DSM324
IC694DSM324
IC694DSM324 Wiring

Rated 4.6/5 based on 5 ratings.
  • IC694DSM324
  • IC694DSM324 Wiring

Product Description


The IC694DSM324 is a GE Fanuc motion controller module belonging to the Rx3i PACSystem. It’s a multi-axis module, which will support standard mode (follower control loop disabled) and follower mode (follower control loop enabled).

The modules come with electronic CAM functionality, an analog I/O port that is used for connection to a PC, and switch inputs for every servo axis. For programming and configuration purposes, the module uses a single point of connection with firmware being saved in flash memory and updated through the COMM port. Storage is non-volatile and can hold up to 10 programs as well as 40 subroutines. Furthermore, it comes with a powerful set of motion program instructions designed for use by 1 to 4 axes.

The IC694DSM324 is equipped with eight LED indicators for displaying the status of the module. The STATUS LED is usually ON, which means the device is working properly. If the LED goes out, this indicates an error and a non-functional module. During module configuration, the CONFIG LED is ON. The FSSB LED is ON when there are FSSB communications and BLINKS during setup. There are also axis-enabled LEDs that come ON when axis 1 to 4 drives are enabled.

The FSSB connector allows for fiber connection to servo amplifiers for command / instructions exchange and diagnostics. It normally has a protection cap to avoid damage. The RJ-11 COMM port is used for downloading of firmware updates. The module also comes with two ports for 24 VDC and 5 VDC power. Pre-manufactured cables come in 1 meter and 3 meter lengths. The IC694DSM324 should be connected to frame ground using the ground terminal located at the bottom of the module. The recommended grounding resistance should be 100 ohms or less. 

Technical Specifications


Module Type: Servo Motion
Number of Slots: 1 (single slot)
Backplane Support: Universal Backplane
Analog Inputs: 2
Analog Outputs:  2
Power Consumption:   1360 mA @ 5 VDC

 

 

GE Intelligent Platforms / GE Fanuc GE RX3i PacSystem

SKU 2178331  UPC 0799705793392

Part Number: IC694DSM324 / ic694dsm324
Mfr/Brand Name: GE Automation
Mfr Number: IC694DSM324 / ic694dsm324
Type: Motion Controller Module (Fiber Optic Interface)

Troubleshooting and Product Information for IC694DSM324

Download product information, troubleshooting guides and operation manuals to get your PLC operational.

New IC694DSM324
Price: $3,004
3 In Stock
1 Year Warranty

*Need a Specific Revision?

New Surplus IC694DSM324
Price: $2,546
1 In Stock
3 Year PDF Supply Warranty

*What is New Surplus?

Save
 16%
Reman IC694DSM324
Price: $1,476
1
In Stock

2 Year PDF Supply Warranty

*What is Remanufactured?

Save
 51%
Repair Your IC694DSM324
Price: $1,180
1 Year PDF Supply Warranty
Call For Assistance
1-800-360-6802

Other IC694DSM324

Available Revisions:

Confirm Your Revision Number

1C694DSM324 , GEFIC694DSM324 , CIMIC694DSM324

 Coming soon 

Troubleshooting IC694DSM324

Troubleshooting information is available on IC694DSM324's website page; it also includes a datasheet user-manual and a wiring diagram.


Repair your IC694DSM324

PDF Supply can repair your IC694DSM324 in 3-5 business days. And PDF Supply stands by all of its repairs with a 1 year customer satisfaction warranty.

 

Customer Questions and Answers


  • Question:  What is an IC694DSM324?  Answer:  The IC694DSM324 is a Digital Servo Motion module from the GE Fanuc RX3i Series.
  • Question: What does IC694DSM324 support?  Answer:
    • This module supports 2 control loop configurations:
      • Standard Mode (Follower Control Loop Disabled)
      • Follower Mode (Follower Control Loop Enabled)
  • Question:  With what can IC694DSM324 be used?  Answer:  This module can be used with GE Fanuc βi Series digital servo amplifiers and motors.
  • Question:  How fast is the block processing time?  Answer:  Under 5 milliseconds
  • Question:  Is there electronic CAM capability?  Answer:  Yes
  • Question:  What are some of the features of IC694DSM324?  Answer:
    • Velocity Feed forward and Position Error Integrator
    • High resolution of programming units
    • Simple and powerful motion program instruction set
    • Simple 1-4 axis motion programs
    • Non-volatile storage for 10 programs and 40 subroutines
    • Single-point-of-connect for programming and configuration
    • Firmware is stored in flash memory and is updated via COMM port
    • Recipe programming using command parameters
    • Home and overtravel switch inputs for each Servo Axis
    • 2 position capture strobe inputs for each axis
    • 5v, 24v, and analog I/O for use by PLC
    • Incremental Quadrature Encoder input on each axis for Encoder/Analog mode
    • 13 bit Analog Output can be controlled by PLC or used as Digital Servo Tuning monitor
    • High speed digital output (four each 24V and four each 5V) via on-board Local Logic control
  • Question:  What should I do if my IC694DSM324 is not working properly?  Answer:  Your IC694DSM324 may need repair

For more information on the IC694DSM324 Digital Servo Motion Module of the GE Fanuc RX3i Series, please see the Datasheet User-Manual.

 

Need To Order A Specific Revision?

Give us a call at 1-800-360-6802 or 1-919-535-3180.

We can help you with your Revision specific needs.


Free Overnight delivery on orders over $500!

What is New Surplus?

These “New Surplus” units are a great cost saving alternative. This product is sealed in the original manufacturer’s packaging with all sub-assemblies and documentation. May indicate older date code. Comes with a PDF Supply 3-year warranty.


Free Overnight delivery on orders over $500!


What is Surplus New?

Surplus New - New unused and includes all sub-assemblies and documentation. Product may ship in manufacturer or PDF Supply packaging. May indicate older date code. Includes a PDF Supply 3 Year Warranty.


Free Overnight delivery on orders over $500!


What is Reconditioned?

Reconditioned products from PDF Supply are a cost-effective alternative to new and obsoleted PLC products. Every part is reconditioned down to the circuit board level and updated to the latest revision. All parts are thoroughly inspected and hand-cleaned before being functionally tested in a fully configured system.


Our Reconditioned Products always come with a PDF Supply 2-Year Warranty.

Free Overnight delivery on orders over $500!


What is a Verified Substitute?

A verified substitute new product is a "drop in" replacement designed with identical specifications as the OEM product. It will meet all electrical and dimensional charactertics at a substanstially reduced price.


Free Overnight delivery on orders over $500!


Download Lastest Documentation


Please visit this manufacturer's website to download the lastest manuals and datasheets.


Lowest Price Guarantee


We stand behind our prices with a lowest price guarantee. If you find a legacy GE PLC part advertised for less on an authorized GE PLC distributor website, simply contact us and send us a link to the lower advertised price. We will match that price and ship overnight FREE. The item must be in stock, in similar condition and be able to ship same day.

Free Shipping



FREE Overnight Delivery for Continental US orders over $500!

FREE Ground Delivery for Continental US orders under $500!

US orders placed Monday - Friday before 5pm EST will ship same day.

Canada/Mexico orders placed Monday - Friday before 3:30pm EST will ship same day.

International orders will ship the following business day.