1-919-535-3180 | 1-800-360-6802

GE / IP FANUC Series 90/30 In Stock

World's Largest Warehouse

of GE 90-30, Genius, and RX7i



Mon-Fri 8AM-5PM EST



Rated 4.7/5 Based on 17 ratings.

Rate your purchase of the IC694MDL340

SKU 2178021  UPC 0518698090352




1 In Stock

✓  2 Year PDF Supply Warranty

*Need a Specific Revision?



2 In Stock

✓  2 Year PDF Supply Warranty

*What is Remanufactured?

Repair Service


5-10 Days

✓  2 Year PDF Supply Warranty

*What is Fast Repair?

Other Available Revisions for the IC694MDL340 IC694MDL340AIC694MDL340-LT

Common misspellings:
  • 1C694MDL340
  • IC69AMDL340
  • IC694MD1340
  • IC694MDL3A0
  • IC694MDL34o
  • IC694MDL340

Technical Specifications for IC694MDL340

ManufacturerGE Fanuc
SeriesRX3i PACSystems
Part NumberIC694MDL340
Product TypeOutput Module
Rated Voltage120V AC
Output Current0.5 A
Output Points16 (2 groups of 8)
Frequency50/60 Hz
Output Voltage Range85 to 132V AC
Operating Temperature0 to 60 degrees Celsius

Product Description

The IC694MDL340 is a 120 VAC, 0.5 amp output module with 16 output points manufactured by GE Fanuc for the Rx3i PACSystem. The 16 points are in two groups of eight. Each group is powered by its own common, but the commons are distinct and not connected. Each group of the IC694MDL340 output module can be powered from the same supply or used in a different phase. Both groups are protected from potential power surges by a 3 amp fuse. Each output is also equipped with an RC snubber that eliminates noise that may exist on the power line.       

This module provides a high degree of inrush current, which allows the outputs to control a variety of inductive and incandescent loads. Required AC Power to operate loads must be user-supplied. Individually numbered LEDs on the front of the IC694MDL340 module share valuable info such as output performance and blown fuses. The red LED labeled “F” turns ON if either of the fuses become non-functional. A load must be connected to the blown fuse for the LED indicator to emit status. Two red bands warn the user of high voltage danger. The IC694MDL340 module can be installed in any RX3i system I/O slot. Its power requirements are 315mA with all outputs ON powered by a 5 volt bus on the backplane. The module’s output voltage range is between 85 to 132 volts AC.

Technical Specifications

Rated Voltage:   120 volts AC
# of Outputs: 16 (2 groups of 8)
Freq: 50/60 Hz
Output Current: 20 Amps max
Output Voltage Range:   85 to 132 volts AC
Power Consumption: 315 mA from 5 V bus  



The IC694MDL340 module is an output module manufactured by GE Fanuc Automation as part of the RX3i PACSystems product series. It features a voltage rating of 120 Volts AC, and it operates on output current of 0.5 Amps for every output point. This module features an inrush current rating of 20 Amps, and an output voltage of 85 to 132 Volts AC at 50 to 60 Hertz frequency. The GE Fanuc IC694MDL340 output module features 16 output points that are isolated and arranged in 2 different groups with 8 points each, and there is a different common for each of the groups. These groups can be used individually on separate AC power supply phases, or they can be used on the same power supply phase. Each group has an RC snubber which protects the outputs against noise caused by the power lines electrical transients.

The IC694MDL340 Output Module by GE Fanuc comes with a high inrush current that enables the outputs to handle a variety of inductive and incandescent loads. This output module is powered only by an AC source of power, and this power must be supplied by the users in order to run the loads that are linked to the output. The GE Fanuc IC694MDL340 output module operates in environments with a temperature ranging from 0 and 60 degrees Celsius and it features a non-operating temperature range of -40 and 85 degrees Celsius. This module can handle 5 to 95 percent relative humidity without condensation. Additionally, this module comes with a 10 to 57 Hertz vibrational rating and 0.0524 millimeters of peak displacement. The shock rating of this output module is 15 G for 11 milliseconds.

Technical Information


Rated Voltage

120 V ac

Output Voltage Range

85 to 132Vac, 50/60 Hz

Outputs per Module

16 (two groups of eight outputs  each)



Field to Backplane (optical) and to Frame Ground

250 V ac continuous; 1500 V ac for 1  minute

Group to Group

250 V ac continuous; 1500 V ac for 1 minute

Output Current

0.5 amp maximum per point 3 amps maximum per group

Output  Characteristics


Inrush Current

20 amps maximum for one cycle

Minimum Load Current

50 mA

Output  Voltage Drop

1.5  volts maximum

Output Leakage Current

2 mA maximum at 120 V ac

On  Response Time

1 ms maximum

Off  Response Time

1/2 cycle maximum

Power Consumption

315 mA (all outputs ON) from 5 volt bus on backplane

Fuses (quantity 2)

3 Amps, part number 44A724627-111. Refer to Module Fuse List, Section for more information.


Troubleshooting IC694MDL340

Troubleshooting information is available on IC694MDL340's website page; it also includes a datasheet user-manual and a wiring diagram.


Repair your IC694MDL340

PDF Supply can repair your IC694MDL340 in 3-5 business days. And PDF Supply stands by all of its repairs with a 1 year customer satisfaction warranty.

Customer Questions and Answers

  • Question:  What is an IC694MDL340?  Answer:  The IC694MDL340 is a 16-Point, 0.5 Amp, 120 Volt AC, Output module from the GE Fanuc RX3i Series.
  • Question:  What does IC694MDL340 provide?  Answer:  This module provides 16 output points in 2 isolated groups of 8 points. 
  • Question:  How many commons are there?  Answer:  Each group has a separate common and the 2 commons are not tied together inside the module.
  • Question:  What can the groups be used on?  Answer:  Used on different phases on the AC supply or powered from the same supply. 
  • Question:  Each group is protected with what?  Answer:  Each group is protected with a 3 Amp fuse.
  • Question:  An RC snubber protects against what?  Answer:  An RC snubber protects each output against transient electrical noise on the power line.
  • Question:  IC694MDL340 provides a high degree of inrush current for what reason?  Answer:  IC694MDL340 provides a high degree of inrush current so the outputs can control a wide range of inductive and incandescent loads. 
  • Question:  AC power to operate loads connected to outputs must be supplied by what?  Answer:  It must be supplied by the user.
  • Question:  This module requires what kind of power source?  Answer:  AC Power
  • Question:  Individual numbered LEDs show what?  Answer:  Individual numbered LEDs show the ON/OFF status of each output point. 
  • Question:  The red LED (F) turns ON when what happens?  Answer:  The red LED turns ON if either of the fuses blow. A load must be connected to the blown fuse for the indicator to light.
  • Question:  The red bands on the label show what?  Answer:  They show that IC694MDL340 is a high-voltage module. 
  • Question:  Into what slot can IC694MDL340 be installed?  Answer:  This module can be installed in any I/O slot of an RX3i system.
  • Question:  What should I do if my IC694MDL340 is not working properly?  Answer:  Your IC694MDL340 may need repair

For more information on the IC694MDL340 16-Point, 0.5 Amp, 120 Volt AC, Output Module of the GE Fanuc RX3i Series, please see the Datasheet User-Manual. 

ST. LOUIS, Feb. 1, 2019 – Emerson today announced it has completed the purchase of Intelligent Platforms from General Electric.
All online orders placed before 4:30 PM EST “SHIPS SAME DAY FREE!" World’s largest warehouse of Factory Sealed GE 90-30 PLC, GENIUS I/O and RX7i PACSystem.highlight_off

PDF Electric & Supply Inc. sells new, new surplus and refurbished products which are sourced through independent channels. All warranties and support, if applicable, are with PDF Electric & Supply Inc. and not the manufacturer. PDF Electric & Supply Inc. is not an authorized distributor or representative for the listed manufacturers and makes no representations as to any quality control performed by any listed manufacturer on the products. The products listed on this website may vary as to their country of origin; the accessories, and other items included with the product; and the language used on the packaging, the parts, and any related instructions or printed material related to the products. This website is not sanctioned or approved by any manufacturer or tradename listed. Designated trademarks, brand names and brands appearing herein are the property of their respective owners.