1-919-535-3180 | 1-800-360-6802

GE / IP FANUC Series 90/30 In Stock

World's Largest Warehouse

of GE 90-30, Genius, and RX7i



Mon-Fri 8AM-5PM EST



RX3i MDL930 Digital I/O

Rated 4.5/5 Based on 10 ratings.

Rate your purchase of the IC694MDL930

SKU 2173248  UPC 0424205512487




7 In Stock

✓  2 Year PDF Supply Warranty

*Need a Specific Revision?

New Surplus


4 In Stock

✓  3 Year PDF Supply Warranty

*What is New Surplus?

Repair Service


5-10 Days

✓  2 Year PDF Supply Warranty

*What is Fast Repair?

Other Available Revisions for the IC694MDL930 IC694MDL930AIC694MDL930BIC694MDL930CIC694MDL930-LT

Common misspellings:
  • 1C694MDL930
  • IC69AMDL930
  • IC694MD1930
  • IC694MDL93o
  • IC694MDL930

Technical Specifications for IC694MDL930

ManufacturerGE Fanuc
SeriesRX3i PACSystems
Part NumberIC694MDL930
Product TypeAC/DC Output Module
Operating Voltage5 to 30 Volts DC, 5 to 250 Volts AC
Switching Current4.0 Amps per Point
I/O Capacity8 Individually-Isolated Relay Outputs
Point to Point IsolationYes
Maximum Backplane Draw6.0 Milliamps
Inrush Rating5.0 Amps

Product Description

The IC694MDL930 is an 8-Point, 4 Amp, Isolated Relay, Output module from the GE Fanuc RX3i Series.  This relay provides 8 normally-open relay circuits for controlling output loads.  See specifications for this unit on IC694MDL930's website page.

Technical Specifications

Rated Voltage: 24 volts DC, 120/240 volts AC
# of Outputs: 8 (isolated)
Freq: 50/60Hz (A/C only)
Output Current:  2A per point, 4 A resistive max
Output Voltage Range:   5 to 30VDC, 5 to 250 VAC
Power Consumption: 6 mA from 5V bus, 70mA from 24V relay



The IC694MDL930 Output Module is an AC/DC output module manufactured as part of the RX3i PACSystems series. It is an 8-channel relay output module manufactured by GE Fanuc Automation as a member of the RX3i PACSystems discrete I/O PLC product line. The IC694MDL930 Output Module is intended to provide the interface between external output devices like the motor starters, solenoids, and indicators and the RX3i PLCs. It comes with 8 individually-isolated and normally-open relay outputs. Each of these outputs can be used to switch loads of 4 Amps at maximum, with each of the output points equipped with a distinct common output terminal. The GE Fanuc IC694MDL930 Output Module uses an external power supply for its operation. The users can use it with a DC or AC power module with power ratings of 24 Volts DC or 120 to 240 Volts AC for powering the connected field devices.

The GE Fanuc IC694MDL930 AC/DC Output Module operates on a voltage ranging from 5 to 250 Volts AC or 5 to 30 Volts DC at a frequency rate of 50 to 60 Hertz. The point-to-point output isolation rating of this unit is 1500 Volts AC for 60 seconds or 250 volts AC continuous. This output module features 8 individually-isolated normally-open relay type outputs with an all-out output current load of 4 Amps per point and or 20 Amps per module. The GE Fanuc IC694MDL930 AC/DC Output Module comes with 6.0 milliamps of maximum backplane current at 5.0 Volts DC. It also has 10.0 milliamps of minimum output load per point. It has 5 Amps of maximum inrush current rating and 10 milliseconds of response time for switching on and switching off.

Technical Information


Rated Voltage

24 volts DC, 120/240 VAC (nominal - see the following table for exceptions)

Operating Voltage

5 to 30 volts DC


5 to 250 VAC, 50/60 Hz

Outputs per Module

Eight isolated outputs



Field to Backplane and to Frame Ground

250 VAC continuous;

1500 VAC for 1 minute

Point to Point

250 VAC continuous; 1500 VAC for 1 minute

Maximum Load

4 Amps resistive maximum per output


2 Amps pilot duty per output


20 Amps maximum per module for UL installations

Maximum Load depends on the ambient temperature as shown below

Minimum Load


Maximum Inrush

5 Amps

On Response Time

15ms maximum1

Off Response Time

15ms maximum1

Power Consumption

6mA (all outputs on) from 5 volt bus on backplane


70mA (all outputs on) from relay 24V bus on backplane

1 When this module is used with DC power supply IC695PSD040 or PSD140, special precautions should be taken because dropouts in the source voltage will be seen by this module and may cause relay dropouts.



Troubleshooting IC694MDL930

Troubleshooting information is available on IC694MDL930's website page; it also includes a datasheet user-manual and a wiring diagram.


Repair your IC694MDL930

PDF Supply can repair your IC694MDL930 in 3-5 business days. And PDF Supply stands by all of its repairs with a 1 year customer satisfaction warranty.

Customer Questions and Answers

  • Question:  What is an IC694MDL930?  Answer:  The IC694MDL930 is an 8-Point, 4 Amp, Isolated Relay, Output module from the GE Fanuc RX3i Series.
  • Question:  What does IC694MDL930 provide?  Answer:  This module provides 8 normally-open relay circuits for controlling output loads. 
  • Question:  What is the output switching capacity of each circuit?  Answer:  It is 4 Amps. 
  • Question:  Each output point is set up how?  Answer:  isolated from the other points and every point has a separate common power output terminal. 
  • Question:  What can the relay outputs control?  Answer:  They can control a wide range of output devices such as: motor starters, solenoids, and indicators. 
  • Question:  Where must the power come from to operate the field devices connected to IC694MDL930?  Answer:  The user must supply the AC or DC power for operation. 
  • Question:  Individual numbered LEDs show what?  Answer:  They show the ON/OFF status of each output point. 
  • Question:  The red bands on the label show what?  Answer:  They show that IC694MDL930 is a high-voltage module.
  • Question:  Into what slot can IC694MDL930 be installed?  Answer:  This module can be installed in any I/O slot of an RX3i system.
  • Question:  What should I do if my IC694MDL930 is not working properly?  Answer:  Your IC694MDL930 may need repair

For more information on the IC694MDL930 8-Point, 4 Amp, Isolated Relay, Output Module of the GE Fanuc RX3i Series, please see the Datasheet User-Manual. 

Release History





May 2015

Change in fab color from Green to Blue. No change in form-fit- functionality.

IC694 MDL930C

Jan 2015

Updated modules are RoHS converted product with applicable exemptions.

IC693/IC694 MDL930A

Aug. 2008

Initial release.


ST. LOUIS, Feb. 1, 2019 – Emerson today announced it has completed the purchase of Intelligent Platforms from General Electric.
All online orders placed before 4:30 PM EST “SHIPS SAME DAY FREE!" World’s largest warehouse of Factory Sealed GE 90-30 PLC, GENIUS I/O and RX7i PACSystem.highlight_off

PDF Electric & Supply Inc. sells new, new surplus and refurbished products which are sourced through independent channels. All warranties and support, if applicable, are with PDF Electric & Supply Inc. and not the manufacturer. PDF Electric & Supply Inc. is not an authorized distributor or representative for the listed manufacturers and makes no representations as to any quality control performed by any listed manufacturer on the products. The products listed on this website may vary as to their country of origin; the accessories, and other items included with the product; and the language used on the packaging, the parts, and any related instructions or printed material related to the products. This website is not sanctioned or approved by any manufacturer or tradename listed. Designated trademarks, brand names and brands appearing herein are the property of their respective owners.