1-919-535-3180 | 1-800-360-6802

GE / IP FANUC Series 90/30 In Stock

World's Largest Warehouse

of GE 90-30, Genius, and RX7i



Mon-Fri 8AM-5PM EST



RX3i MDL931 Digital I/O

Rated 4.7/5 Based on 8 ratings.

Rate your purchase of the IC694MDL931

SKU 2171143  UPC 0102640829406




7 In Stock

✓  2 Year PDF Supply Warranty

*Need a Specific Revision?



4 In Stock

✓  2 Year PDF Supply Warranty

*What is Remanufactured?

Repair Service


5-10 Days

✓  2 Year PDF Supply Warranty

*What is Fast Repair?

Other Available Revisions for the IC694MDL931 IC694MDL931AIC694MDL931BIC694MDL931-LT

Common misspellings:
  • 1C694MDL931
  • IC69AMDL931
  • IC694MD1931
  • IC694MDL93l
  • IC694MDL931

Product Description

The IC694MDL931 is an 8-Point, 8 Amp, Isolated Relay, Output module from the GE Fanuc RX3i Series.  This relay provides 4 normally-closed and 4 Form C relay circuits for controlling output loads.  See specifications for this unit on IC694MDL931's website page.

Technical Specifications

Rated Voltage: 24 volts DC, 120/240 volts AC
# of Outputs: 8 (isolated)
Freq: 50/60Hz (A/C only)
Output Current:  20A per module, 8 A resistive max
Output Voltage Range:   5 to 30VDC, 5 to 250 VAC
Power Consumption: 6 mA from 5V bus, 110mA from 24V relay



Technical Information


Rated Voltage

24 volts DC, 120/240 VAC, 50/60 Hz (nominal - see the following table for exceptions)

Output Voltage Range

5 to 30 volts DC


5 to 250 VAC, 50/60 Hz

Outputs per Module

Eight isolated outputs



Field to Backplane and to Frame Ground

250 VAC continuous;

1500 VAC for 1 minute

Point to Point

250 VAC continuous; 1500 VAC for 1 minute

Maximum Load

8 Amps resistive maximum per output


20 Amps maximum per module for UL installations Maximum load depends on ambient temperature as shown.

Minimum Load


Inrush Current

8 Amps maximum for one cycle

On Response Time

15ms maximum1

Off Response Time

15ms maximum1

Output Leakage Current

1mA maximum at 250 VAC, (25°C (77°F))

Power Consumption

6mA (all outputs on) from 5 volt bus on backplane 110mA (all outputs on) from relay 24V bus on backplane

1 When this module is used with DC power supply IC695PSD040 or PSD140, special precautions should be taken because dropouts in the source voltage will be seen by this module and may cause relay dropouts.



Troubleshooting IC694MDL931

Troubleshooting information is available on IC694MDL931's website page; it also includes a datasheet user-manual and a wiring diagram.


Repair your IC694MDL931

PDF Supply can repair your IC694MDL931 in 3-5 business days. And PDF Supply stands by all of its repairs with a 1 year customer satisfaction warranty.

Customer Questions and Answers

  • Question:  What is an IC694MDL931?  Answer:  The IC694MDL931 is an 8-Point, 8 Amp, Isolated Relay, Output module from the GE Fanuc RX3i Series.
  • Question:  What does IC694MDL931 provide?  Answer:  This module provides 4 normally-closed and 4 Form C relay circuits for controlling output loads. 
  • Question:  What is the output switching capacity of each circuit?  Answer:  It is 8 Amps. 
  • Question:  Each output point is set up how?  Answer:  Each output relay is isolated from the other relays and every relay has a separate common power output terminal. 
  • Question:  What can the relay outputs control?  Answer:  They can control a wide range of output devices such as: motor starters, solenoids, and indicators. 
  • Question:  Where must the power come from to operate the field devices connected to IC694MDL931?  Answer:  The user must supply the AC or DC power for operation. 
  • Question:  Individual numbered LEDs show what?  Answer:  They show the ON/OFF status of each output point. 
  • Question:  The red bands on the label show what?  Answer:  They show that IC694MDL931 is a high-voltage module.
  • Question:  Into what slot can IC694MDL931 be installed?  Answer:  This module can be installed in any I/O slot of an RX3i system.
  • Question:  What should I do if my IC694MDL931 is not working properly?  Answer:  Your IC694MDL931 may need repair

For more information on the IC694MDL931 8-Point, 8 Amp, Isolated Relay, Output Module of the GE Fanuc RX3i Series, please see the Datasheet User-Manual. 

Release History





May 2015

Change in fab color from Green to Blue. No change in form-fit- functionality.

IC694 MDL931B

Jan 2015

Updated modules are RoHS converted product with applicable exemptions.

IC693/IC694 MDL931A

Aug. 2008

Initial release.


ST. LOUIS, Feb. 1, 2019 – Emerson today announced it has completed the purchase of Intelligent Platforms from General Electric.
All online orders placed before 4:30 PM EST “SHIPS SAME DAY FREE!" World’s largest warehouse of Factory Sealed GE 90-30 PLC, GENIUS I/O and RX7i PACSystem.highlight_off

PDF Electric & Supply Inc. sells new, new surplus and refurbished products which are sourced through independent channels. All warranties and support, if applicable, are with PDF Electric & Supply Inc. and not the manufacturer. PDF Electric & Supply Inc. is not an authorized distributor or representative for the listed manufacturers and makes no representations as to any quality control performed by any listed manufacturer on the products. The products listed on this website may vary as to their country of origin; the accessories, and other items included with the product; and the language used on the packaging, the parts, and any related instructions or printed material related to the products. This website is not sanctioned or approved by any manufacturer or tradename listed. Designated trademarks, brand names and brands appearing herein are the property of their respective owners.