1-919-535-3180 | 1-800-360-6802

GE / IP FANUC Series 90/30 In Stock

World's Largest Warehouse

of GE 90-30, Genius, and RX7i



Mon-Fri 8AM-5PM EST



RX3i CEP001 Accessory

Rated 0/5 Based on ratings.

Rate your purchase of the IC695CEP001
Image of IC695CEP001

SKU 0  UPC 00


PDF Supply Company, LLC is not an authorized distributor for GE Fanuc Emerson



3 In Stock

✓  2 Year PDF Supply Warranty

*Need a Specific Revision?

Surplus New


11 In Stock

✓  3 Year PDF Supply Warranty

*What is Surplus New?

Repair Service


5-10 Days

✓  2 Year PDF Supply Warranty

*What is Fast Repair?

Common misspellings:
  • 1C695CEP001
  • IC695CEPo01
  • IC695CEP0o1
  • IC695CEP00l
  • IC695CEP001

Product Description

The IC695CEP001 is a CEP Carrier Module from the GE Fanuc RX3i Series.  This module interfaces a remote node to one PACSystems RX3i I/O module to a PROFINET I/O Local Area Netework (LAN).  See specifications for this unit on IC695CEP001's website page.

Technical Specifications

Module Type: I/O Link Interface
LEDs: PWR1, PWR2, OK, Connect, PRT1, PRT2
Mounting:   Din Rail or Panel
I/O Data: 512 bytes of inputs and 512 bytes of outputs 
Ethernet Ports:  (2) RJ-45
USB Ports: (1) for firmware upgrades only



Technical Information


Note: For  product standards, general operating specifications, and installation  requirements, refer  to the

PACSystems RX3i System Manual (GFK-2314).

PROFINET support

PROFINET  Version 2.3 Class A IO-Device



RX3i Controller version required

CPU320/CPU315 Primary Firmware Release 8.95 or later CPU320/CPU315 Boot Firmware Release 5.10 or later CPE310/CPE305 Primary Firmware Release 8.95 or later CPE310/CPE305 Boot Firmware Release 7. 10 or later CRU320 Primary Firmware Release 8.95

CRU320 Boot Firmware Release 5.10 or later

IC695PNC001 PROFINET  IO-controller  with firmware version 2.26 or later

RXi Controller version required

RXi Controller, ICRXICTL000, with firmware version 7.80 or later is compatible with CEP001 up to version 2.01, but is not compatible with CEP001 version 2.30.

Proficy Machine Edition version required

Version 8.6 with SIM 3 or later

Power requirements1

IC695CEP001: 5.25W (0.22 A) at 24 Vdc with or without Expansion Carrier (IC694CEE001) DC power supply input range: 19.2 to 30 Vdc

Module dimensions

177.2 x 51 x 35 mm (6.98” x 2.01” x 1.38”). Same for CEP001 and CEE001.

Operating  temperature

0°C to 60°C (32°F to 140°F) maximum surrounding air temperature

Number of Ethernet port connectors

IC695CEP001: Two RJ-45 10/100Base-TX receptacles IC694CEE001: None

USB connector (for firmware upgrades)

IC695CEP001: One Micro-B connector. USB 2.0 compliant running at full-speed (12 MHz) in  device mode

IC694CEE001: None

PNS status and control bits

32 input status bits and 32 output control bits

I/O data update on the PROFINET LAN

Configurable: 1ms, 2ms, 4ms, 8ms, 16ms, 32ms, 64ms, 128ms, 256ms and 512ms

Number of IP addresses

One; supports Classless Inter-Domain Routing (CIDR)

Number of MAC addresses

Three; one per external port and one internal. External MAC addresses are only used for specialized Ethernet protocols such as MRP or LLDP.



I/O station maximum limits


Number of I/O modules per  station

IC695CEP001: One

IC695CEP001 with IC694CEE001: Two


I/O data per station

1024 bytes total

512 bytes of input data

512 bytes of output data



Configured using Proficy Machine Edition when used with a PACSystems RX3i PROFINET Controller module as part of an RX3i High-speed I/O LAN system.

V2.3 GSDML file available for import into 3rd-Party  tools.



Troubleshooting IC695CEP001

Troubleshooting information is available on IC695CEP001's website page; it also includes a datasheet user-manual and a wiring diagram.


Repair your IC695CEP001

PDF Supply can repair your IC695CEP001 in 3-5 business days. And PDF Supply stands by all of its repairs with a 1 year customer satisfaction warranty.

Customer Questions and Answers

  • Question:  What is an IC695CEP001?  Answer:  IC695CEP001 is a CEP Carrier Module from the GE Fanuc RX3i Series.
  • Question:  What does IC695CEP001 do for the RX3i system?   Answer:  This module interfaces a remote node to one PACSystems RX3i I/O module to a PROFINET I/O Local Area Netework (LAN).
  • Question:  How does the IC695CEP001 operate?  Answer:  The RX3i CEP Carrier works as a PROFINET IO-Device.  
  • Question:  What are some of the operating features?  Answer:  
    • Scanning all the modules within the remote node
    • Publishing data on the PROFINET network
    • Receiving data from a PROFINET IO-Controller on the network
    • Managing PROFINET communication and module configuration
    • Managing the state of the /O when communication is lost.
    • Publishing fault information (alarms, diagnostics, etc) to the PROFINET IO-Controller
  • Question:  Where must IC695CEP001 be located?  Answer:  IC695CEP001 can be installed in any available backplane slot.
  • Question:  What should I do if my IC695CEP001 is not working properly?  Answer:  Your IC695CEP001 may need repair.

For more information on the IC695CEP001 CEP Carrier Module of the GE Fanuc RX3i Series, please see the Datasheet User-Manual.

Release History


Firmware Release








Oct 2016

Added support for the Remote Get HART Device Information COMMREQ. Information from a HART device connected to an RX3i Analog Module in an IC695CEP001 RX3i CEP Carrier may be read into the user application using the Remote Get HART Device

Information COMMREQ.



Dec 2015

Added support for additional I/O Modules (refer to the section

Supported I/O Modules)



June 2015

Added support for additional I/O Modules (refer to the section

Supported I/O Modules)



June 2015

Added support for additional I/O Modules (refer to the section

Supported I/O Modules) and for HART pass through functionality.






Nov 2014

Added Hot-standby CPU redundancy using PROFINET I/O and support for additional RX3i I/O modules: IC695ALG112,

IC695ALG600, and IC694PSM001



Jan 2014

Initial release

ST. LOUIS, Feb. 1, 2019 – Emerson today announced it has completed the purchase of Intelligent Platforms from General Electric.

Common related search terms: Emerson

All online orders placed before 4:30 PM EST “SHIPS SAME DAY FREE!" World’s largest warehouse of Factory Sealed GE 90-30 PLC, GENIUS I/O and RX7i PACSystem.highlight_off

PDF Supply Company, LLC sells new, new surplus and refurbished products which are sourced through independent channels. All warranties and support, if applicable, are with PDF Supply Company, LLC and not the manufacturer. PDF Supply Company, LLC is not an authorized distributor or representative for the listed manufacturers and makes no representations as to any quality control performed by any listed manufacturer on the products. The products listed on this website may vary as to their country of origin; the accessories, and other items included with the product; and the language used on the packaging, the parts, and any related instructions or printed material related to the products. This website is not sanctioned or approved by any manufacturer or tradename listed. Designated trademarks, brand names and brands appearing herein are the property of their respective owners.