1-919-535-3180 | 1-800-360-6802
sales@pdfsupply.com

GE / IP FANUC Series 90/30 In Stock

World's Largest Warehouse

of GE 90-30, Genius, and RX7i

1-919-535-3180

1-800-360-6802

Mon-Fri 8AM-5PM EST

sales@pdfsupply.com

IC695ETM001

RX3i ETM001 Communication

Rated 4.7/5 Based on 25 ratings.

Rate your purchase of the IC695ETM001
Loading...

SKU 2172460  UPC 0746867781101

disclaimer

Order Today - Ships Today!

*US continental orders placed Monday-Friday before 4:30pm EST!

New

$1777

5 In Stock

✓  2 Year PDF Supply Warranty

*Need a Specific Revision?

New Surplus

$1582

7 In Stock

✓  3 Year PDF Supply Warranty

*What is New Surplus?

Reman

$825

19 In Stock

✓  2 Year PDF Supply Warranty

*What is Remanufactured?

Repair Service

$565

5-10 Days

✓  2 Year PDF Supply Warranty

*What is Fast Repair?

Technical Specifications for IC695ETM001

ManufacturerGE Fanuc
SeriesRX3i PACSystems
Part NumberIC695ETM001
Product TypeEthernet Interface Module
Ethernet Ports2 10/100 Mbps Ports
Serial RS-232 PortYes
Serial Data Rates1200 to 115,200 bps
Hot SwappingSupported
Duplex ModesHalf and Full-Duplex
IP Addresses1

Product Description


The IC695ETM001 is an Ethernet Interface module from the GE Fanuc RX3i Series. The Ethernet Interface Module connects a PACSystems RX3i to an Ethernet network. It enables the RX3i controller to communicate with other PACSystems equipment and with Series 90 and VersaMax controllers.See specifications for this unit on IC695ETM001's website page.

Technical Specifications


Processing Speed: 

200 MHz

Number of Slots: 1 (Single Slot) 
Bus Speed: 10/100 Mbaud
Comm Ports: 2 RJ-45 ports
Protocol Support: SRT, Modbus TCP, Ethernet Global Data (EGD)
Serial Port:   RS-232 Station Manager

 

GE Fanuc manufactures the IC695ETM001 Ethernet interface module as part of the RX3i PACSystems series. This unit is designed and intended to enable controllers in the RX3i PACSystems series to interface with the VersaMax, Series 90-30, and other controllers over the Ethernet Networks. It features an Ethernet Interface that can operate at 10/100 Mbps and that can sense the speed and the type of cable connected. A pair of twisted cable measuring up to 100 meters in length is used to connect network nodes at 10 Mbps. Additionally, a Category 5 twisted-pair cable with a length of 100 meters is used to connect the network nodes at 100 Mbps. The IC695ETM001 Ethernet interface features an Ethernet port that supports the use of full-duplex and half-duplex nodes. Additionally, both straight-through and crossover Ethernet cables can be used for the network connections. This Ethernet interface module supports 1 MAC address along with 1 IP address. It comes with an embedded Ethernet switch that enables the daisy chaining of the Ethernet nodes.

Another notable feature of the GE Fanuc RX3i PACSystems IC695ETM001 Ethernet interface module is an RS-232 serial port. The IC695ETM001 interface module supports data rates ranging from 1200 bps to 115,200 bps. It has an integral station manager function that is accessible via Ethernet and Serial connections, and it also offers supervisory access. Among the services that the station manager function provides are commands for controlling and polling the station, password security, and access to the monitoring logs, configuration parameters, and statistics. The Allen-Bradley IC695ETM001 Ethernet interface module is recommended for the synchronization of timestamps of EGD exchanges via the SNTP protocol.

Technical Information

Specifications

Ethernet processor speed

200 MHz

Connectors

-  Station Manager (RS-232) Port: 9-pin female D-connector

-  Two 10BaseT / 100BaseTX Ports: 8-pin female shielded RJ-45

LAN

IEEE  802.2  Logical Link Control Class I

IEEE 802.3 CSMA/CD Medium Access Control 10/100 Mbps

Number of IP addresses

One

Number of Ethernet Port Connectors

Two. both  are 10BaseT / 100BaseTX  with  auto-sensing  RJ-45 connection.

Embedded Ethernet Switch

Yes – Allows daisy-chaining of Ethernet nodes.

Serial Port

Station Manager Port: RS-232  DCE, 1200  – 115,200 bps.

 

Troubleshooting

Troubleshooting IC695ETM001

Troubleshooting information is available on IC695ETM001's website page; it also includes a datasheet user-manual and a wiring diagram.


Repair your IC695ETM001

PDF Supply can repair your IC695ETM001 in 3-5 business days. And PDF Supply stands by all of its repairs with a 1 year customer satisfaction warranty.

 

 

How to Go Online with an RX3i PLC via Ethernet Cable When the MAC ID Sticker on IC695ETM001 is Missing

Description

To configure an IP address in IC695ETM001 module when one is not assigned, the “Set Temporary IP address” utility is used in Machine Edition. The assigned MAC ID address of the ETM001 needs to be entered in this utility. But if the MAC address ID sticker on the module was lost, how can one go online with PLC via Ethernet cable?

Resolution

An IP address can be configured on the ETM001 Ethernet Interface with the missing MAC Address sticker this way:

  1. Install the ETM001 in slot 3 which does not have the MAC address ID sticker, then insert another ETM001 in slot 4 which has a MAC address ID sticker. Connect the Ethernet cable to the Ethernet interface in slot 4.
  2. If the IP address of ETM001 in slot 3 should be 192.168.1.1, use the “Set Temporary IP address” tool to set temporary IP address of the ETM001 in slot 4 to be 192.168.1.2. Then go online with the ETM001 in slot 4 using that IP address.
  3. Download the hardware configuration to the controller, assigning IP address 192.168.1.1 to the ETM001 in slot 3.
  4. Remove the ETM001 in slot 4, then connect the Ethernet cable to the Ethernet interface on ETM001 in slot 3. Now go online with the module using IP address 192.168.1.1.

To identify the MAC ID of ETM001 in slot 3, “Wireshark network protocol analyzer” or “Station Manager” can be used.

 

Customer Questions and Answers


  • Question:  What is an IC695ETM001?  Answer:  The IC695ETM001 is an Ethernet Interface module from the GE Fanuc RX3i Series.
  • Question:  For what is IC695ETM001 used?   Answer:  IC695ETM001 is used to connect a PACSystems RX3i controller to an Ethernet network. 
  • Question:  What does IC695ETM001 enable the RX3i controller to do?  Answer:  It enables the RX3i controller to communicate with other PACSystems equipment, as well as with Series 90 and VersaMax controllers.
  • Question:  What does IC695ETM001 provide?  Answer:  This module provides TCP/IP communications with other PLCs, host computers (ones that are running the Host Communications Toolkit or programmer software), and computers running the TCP/IP version of the programming software. 
  • Question:  What are some of the features of IC695ETM001?  Answer:
    • Full PLC programming and configuration services
    • Periodic data exchange using Ethernet Global Data (EGD)
    • EGD Commands to read and write PLC and EGD exchange-memory over the network
    • TCP/IP communication services using SRTP
    • Comprehensive station management and diagnostic tools
    • Extended PLC connectivity via IEEE 802.3 CSMA/CD 10 Mbps and 100 Mbps Ethernet LAN port connectors
    • Network switch that has auto negotiate, sense, speed, and crossover detection
    • Direct connection to BaseT (twisted pair) network switch, hub, or repeater without an external transceiver
  • Question:  Does IC695ETM001 have an embedded Ethernet Switch?  Answer:  Yes- this allows daisy chaining of Ethernet nodes.
  • Question:  What should I do if my IC695ETM001 is not working properly?  Answer:  Your IC695ETM001 may need repair.

For more information on the IC695ETM001 Ethernet Interface Module of the GE Fanuc RX3i Series, please see the Datasheet User-Manual.

ST. LOUIS, Feb. 1, 2019 – Emerson today announced it has completed the purchase of Intelligent Platforms from General Electric.
All online orders placed before 4:30 PM EST “SHIPS SAME DAY FREE!" World’s largest warehouse of Factory Sealed GE 90-30 PLC, GENIUS I/O and RX7i PACSystem.highlight_off

PDF Electric & Supply Inc. sells new, new surplus and refurbished products which are sourced through independent channels. All warranties and support, if applicable, are with PDF Electric & Supply Inc. and not the manufacturer. PDF Electric & Supply Inc. is not an authorized distributor or representative for the listed manufacturers and makes no representations as to any quality control performed by any listed manufacturer on the products. The products listed on this website may vary as to their country of origin; the accessories, and other items included with the product; and the language used on the packaging, the parts, and any related instructions or printed material related to the products. This website is not sanctioned or approved by any manufacturer or tradename listed. Designated trademarks, brand names and brands appearing herein are the property of their respective owners.