GE / IP FANUC Series 90/30 In Stock

Call Now

1-800-360-6802

Mon-Fri 8AM-5PM EST

1-919-535-3180

IC695PSD040

Rated 4.5/5 Based on 12 ratings.

Rate your purchase of the IC695PSD040

IC693PWR324 IC695PSD040 In Stock! RX3i 24VDC power supply, 40 watts. IC695P IC695PS IC695PSD PDFsupply also repa IC695PSD040 In Stock! RX3i 24VDC power supply, 40 watts. IC695P IC695PS IC695PSD PDFsupply also repa IC695PSD040

SKU 2170241  UPC 0593797281108

New Surplus

$336

7 In Stock

3 Year warranty

*What is
New Surplus?

Reman

$201

2 In Stock

2 Year warranty

*What is
Remanufactured?

Repair

$155

Fast turnaround

1 Year warranty

1-800-360-6802

Order Today - Ships Today!


*US continental orders placed before 4:30pm EST!

Lowest Price Guarantee

Other Available Revisions for the IC695PSD040 ACAEFGHJLT

Product Description


The IC695PSD040 is a 24 volt DC, 40 Watt Power Supply from the GE Fanuc RX3i Series.  See specifications for this unit on IC695PSD040's website page.

Technical Specifications


Nominal Rated Voltage:   24 volt DC
Input Voltage Range: 18 VDC to 30 VDC
Input Power: 60 Watts
Load Capacity: 40 Watts
Module Type: Universal Base Power Supply
Backplane Support: Universal Backplane Only

 

 

Technical Information

Specifications: 

 

Nominal Rated Voltage

24 VDC

Input Voltage Range

18 to 30 VDC

Input Power

60 Watts maximum at full load

Inrush Current

4 Amps, 100 milliseconds maximum *

Output Power

40 Watts maximum total of both outputs.

5.1 VDC = 30 Watts maximum

3.3 VDC = 30 Watts maximum

Maximum output power depends on ambient temperature, as shown.

Output Voltage

5.1 VDC: 5.0 VDC to 5.25 VDC (5.1 VDC nominal)

3.3 VDC: 3.2 VDC to 3.465 VDC (3.3 VDC nominal)

Output Current

5.1 VDC: 0 to 6 Amps

3.3 VDC: 0 to 9 Amps

Isolation

None

Ripple (all outputs)

50 mV

Noise (all outputs)

50 mV

Ride-through time

10 ms This is the length of time the Power Supply maintains valid outputs if the power source is interrupted. If this Power Supply is used with IC694 and IC693 modules that have relay outputs, special precautions should be taken because dropouts in the source voltage will be seen by the module and may cause relay dropouts.

Wiring Terminals

Each terminal accepts one 14 AWG to 22 AWG wire.

Terminal Current

6 Amps

Number of Daisy-Chained PSD040 Supplies

Up to 2

Installation Environment

For use in Pollution Degree 2 environments only

* The Inrush Current specification is given as a guide for sizing the external power source for the IC695PSD040. Peak inrush current may be higher for shorter durations.

Troubleshooting

Troubleshooting IC695PSD040

Troubleshooting information is available on IC695PSD040's website page; it also includes a datasheet user-manual and a wiring diagram.


Repair your IC695PSD040

PDF Supply can repair your IC695PSD040 in 3-5 business days. And PDF Supply stands by all of its repairs with a 1 year customer satisfaction warranty.

Customer Questions and Answers


  • Question:  What is an IC695PSD040?  Answer:  The IC695PSD040 is a 24 VDC, 40 Watt Power Supply from the GE Fanuc RX3i Series. 
  • Question:  From what input voltage source range does IC695PSD040 operate?  Answer:  This power supply operates from an input voltage source range of 18 VDC to 30 VDC.
  • Question:  What 3 outputs does this power supply have?  Answer:
    • +5.1 VDC output
    • +24 VDC relay output that can be used to power circuits on Output Relay modules
    • +3.3 VDC which, is used internally by RX3i modules with IC695 catalog numbers
  • Question:  How many IC695PSD040's can be installed in a PACSystems RX3i Universal Backplane?  Answer:  Only 1
  • Question:  With what can IC695PSD040 not be used?  Answer:  This power supply cannot be used with other RX3i power supplies in redundant or increased capacity modes. 
  • Question:  What do the 4 LEDs indicate?  Answer:
    • Power (Green/Amber). When this LED is green, it indicates power is being supplied to the backplane. When this LED is amber, power is applied to the power supply, but the power supply switch is off.
    • P/S Fault (Red). When this LED is lit, it indicates the power supply has failed and is no longer supplying sufficient voltage to the backplane.
    • Over Temperature (Amber). When this LED is lit, it indicates the power supply is near or exceeding its maximum operating temperature.
    • Overload (Amber). When this LED is lit, it indicates the power supply is near or exceeding its maximum output capability on at least one of its outputs.
  • Question:  What should I do if my IC695PSD040 is not working properly?  Answer:  Your IC695PSD040 may need  repair.

For more information on the IC695PSD040 24 VDC, 40 Watt Power Supply of the GE Fanuc RX3i Series, please see the Datasheet User-Manual.

Release History

 

Version

Comments

IC695PSD040H

Increases the margin of the 5V and 3.3V under voltage detectors to prevent PS faults during power-up.

IC695PSD040G

Resolves radiated susceptibility and surge issues in the RX3i PSD140 DC power supplies.

IC695PSD040F

Resolves an issue with previous versions of this power supply occasionally failing to power up when installed in a 16-Slot Universal Backplane, IC695CHS016.

IC695PSD040E

Corrected issue with reporting of module identification.

IC695PSD040A

Initial release.

PDF Electric & Supply Inc. sells new, new surplus and refurbished products which are sourced through independent channels. All warranties and support, if applicable, are with PDF Electric & Supply Inc. and not the manufacturer. PDF Electric & Supply Inc. is not an authorized distributor or representative for the listed manufacturers and makes no representations as to any quality control performed by any listed manufacturer on the products. The products listed on this website may vary as to their country of origin; the accessories, and other items included with the product; and the language used on the packaging, the parts, and any related instructions or printed material related to the products. This website is not sanctioned or approved by any manufacturer or tradename listed. Designated trademarks, brand names and brands appearing herein are the property of their respective owners.

TOP