GE / IP FANUC Series 90/30 In Stock
Preowned
PDF Supply Company, LLC is not an authorized distributor for GE Fanuc Emerson
Other Available Revisions for the IC698CPE010 IC698CPE010-AAIC698CPE010-BAIC698CPE010-BBIC698CPE010-BCIC698CPE010-CCIC698CPE010-CDIC698CPE010-CEIC698CPE010-DEIC698CPE010-DFIC698CPE010-DGIC698CPE010-DHIC698CPE010-EJIC698CPE010-EKIC698CPE010-FLIC698CPE010-GMIC698CPE010-GPIC698CPE010-HPIC698CPE010-HQIC698CPE010-JQIC698CPE010-JRIC698CPE010-JSIC698CPE010-JTIC698CPE010-JUIC698CPE010-JVIC698CPE010-JWIC698CPE010-JXIC698CPE010-JZIC698CPE010-Programming Software
Manufacturer | GE Fanuc |
---|---|
Series | RX7i PACSystems |
Part Number | IC698CPE010 |
Product Type | CPU |
CPU | Celeron CPU with 300 MHz speed |
Ethernet Speed | 10/100 Mbps |
Current | 3.2 Amps |
Program Blocks | 512 |
Accuracy | 9 seconds per day |
Temperature | 32 to 140 degrees Fahrenheit |
The IC698CPE010 is a Central Processing Unit from the GE Fanuc RX7i series. This device is capable of controlling industrial machinery and material processes in real-time. It communicates with other devices and modules through a VME64 connection backplane mounted to the rack.
The IC698CPE010 has a 300MHz Celeron microprocessor capable of performing floating point calculations. The standard speed of each Boolean function is 0.33ms per coil. Other features of this device include but are not limited to the following: three embedded serial ports and two Ethernet ports, bit-in-word reference support, symbolic variable support, a Test Edit mode, and data monitoring over the web.
This device has 10 megabytes of RAM memory for data and programming information. This memory is sustained by a CMOS battery. An additional 10 megabytes of non-volatile flash memory (NVRAM) is also provided. The operating system firmware data is stored in flash memory. Firmware can be updated without taking apart the device or replacing the EPROMs.
There are two means to operate the IC698CPE010: the three-position run/stop switch and connecting the device to a computer and running the appropriate software. Connecting this device to a computer is possible via the serial or Ethernet ports. Note: Using the Ethernet port will require IP addressing and a Cat5 cable. For serial connections, the SNP protocol is used. For configuration and programming of this device, Proficy Machine Edition PLC-Logic Developer software is used on the attached computer. Configuration data is secured with a password.
Follow the instructions in the product manual while installing the IC698CPE010. Disable rack power. Document the Media Access Control (MAC) address of the device. Securely mount and ground the device into slot one of the rack, the designated CPU slot. Connect the Ethernet and serial ports. Re-enable power to the rack. Connect the CMOS battery to one of the connectors. Begin programming the device.
Processing Speed: | 300 MHz |
CPU Memory: | 10 Mbytes |
Floating Point: | Yes |
Serial Ports: | 3 |
Serial Protocols: | Modbus RTU Slave, SNP, Serial I/O |
Embedded Comms: | RS-232, RS-486. Ethernet interface |
The IC698CPE010 CPU is a GE Fanuc Central Processing Unit. It is an industrial central processor unit from the RX7i PACSystems series. It helps to control different industrial applications. The CPU comes with a 300 MHz Celeron processor and it supports Ethernet speeds of up to 100 Mbps. The CPU features memory retention for 40 days of nominal power. The CPU has 10 MB of non-volatile flash user memory. It is powered with 5 Volts bus voltage and it has a current rating of 3.2 Amps. It can execute boolean expressions with a speed of 0.195 milliseconds per 1000 Boolean contacts/coils. It has an accuracy of 9 seconds per day. The CPU can monitor up to 16 web server and FTP connections. It is designed to be compact and it weighs only 6.3 kilograms. It can be easily mounted on a rack with the backplane. The operating temperature should be set between 0 and 60 degrees Celsius.
The GE Fanuc IC698CPE010 CPU communicates with the programmer and HMI devices by using Ethernet ports with the VME 64 standard format on the front side of the module. The CPU provides access to bulk memory by using a reference table. It can be programmed by using different programming languages including the ladder diagram, structured text, and functional block diagram languages. The IC698CPE010 CPU is equipped with serial ports that support the Modbus RTU slave, SNP, and Serial I/O protocols. The CPU features support for up to 512 program blocks. It also allows the “test edit” mode that can make modifications for a running program. The IC698CPE010 CPU also supports remote station managers.
Battery Memory retention |
For battery selection, installation and estimated life, refer to the PACSystems Controller Battery and Energy Pack Manual, GFK-2741. |
Program storage |
Up to 10 Mbytes of battery-backed RAM 10 Mbytes of non-volatile flash user memory |
Power requirements CPE010 CPE020 |
+5 VDC: 3.2 Amps nominal +12 VDC: 0.042 Amps nominal -12 VDC: 0.008 Amps nominal +5 VDC: 4.5 Amps nominal +12 VDC: 0.042 Amps nominal -12 VDC: 0.008 Amps nominal |
Operating temperature |
CPE020: 0 to 60°C (32°F to 140°F) with fan tray, required |
Floating point |
Yes |
Boolean execution speed, typical CPE010 CPE020 |
0.33ms per 1000 Boolean contacts/coils 0.14ms per 1000 Boolean contacts/coils |
Time of Day Clock accuracy |
Maximum of 9 seconds per day |
Elapsed Time Clock (internal timing) accuracy |
0.01% maximum |
Embedded communications |
RS-232, RS-485, Ethernet interface |
Ethernet Ports |
Embedded auto-sensing 10/100 Mbps half/full duplex Ethernet interface |
Serial protocols supported |
Modbus RTU Slave, SNP, Serial I/O |
VME Compatibility |
System designed to support the VME64 standard ANSI/VITA 1 |
Program blocks |
Up to 512 program blocks. Maximum size for a block is 128KB. |
Memory |
%I and %Q: 32Kbits for discrete %AI and %AQ: configurable up to 32Kwords %W: configurable up the maximum available user RAM Symbolic: configurable up to 10Mbytes |
Ethernet Interface Specifications |
|
Web-based data monitoring |
Up to 16 web server and FTP connections (combined) |
Ethernet data rate |
10Mb/sec and 100Mb/sec |
Physical interface |
10BaseT RJ45 |
WinLoader support |
Yes |
Number of EGD configuration-based pages |
255 |
Time synchronization |
SNTP |
Selective consumption of EGD |
Yes |
Load EGD configuration from CPU to programmer |
Yes |
Remote Station Manager over UDP |
Yes |
Local Station Manager (RS-232) |
Dedicated RS-232 port |
Configurable Advanced User Parameters |
Yes |
Troubleshooting IC698CPE010
Troubleshooting information is available on IC698CPE010's website page; it also includes a datasheet user-manual and a wiring diagram.
Repair your IC698CPE010
PDF Supply can repair your IC698CPE010 in 3-5 business days. And PDF Supply stands by all of its repairs with a 1 year customer satisfaction warranty.
For more information on the IC698CPE010 Central Processing Unit of the GE Fanuc RX7i Series, please see the Datasheet User-Manual.
Revision | Date | CPU Version | Ethernet Version |
CPE020-KAA | May. 13 | 6.75 | 6.2 |
CPE010-JX | May. 13 | 6.75 | 6.2 |
-KZ | Jun. 12 | 6.75 | 6.13 |
-JZ | Apr. 12 | 6.75 | 6.13 |
-JY | Feb. 12 | 6.75 | 6.12 |
-JX | Nov. 11 | 6.75 | 6.1 |
-JW | Jul. 11 | 6.71 | 6.1 |
-JV | Mar. 10 | 6.01 | 6 |
-JU | Sep. 09 | 6 | 6 |
-JT | Dec. 08 | 5.5 | 5.51 |
-JS | May. 08 | 5.5 | 5.5 |
-JR | Dec. 07 | 5 | 5.01 |
-JQ | Oct. 07 | 5 | 5 |
-HQ | Aug. 07 | 5 | 5 |
-HP | Jul. 07 | 4.02 | 4 |
-GP | Dec. 06 | 4.02 | 4 |
-GN | Sep. 06 | 4 | 4 |
-GM | May. 06 | 3.5 | 3.81 |
-FL | Nov. 05 | 3.5 | 3.6 |
-EK | Sep. 05 | 3.5 | 3 |
-EJ | Jul. 05 | 3.11 | 3 |
-DH | Apr. 05 | 3.1 | 3 |
-DG | Apr. 05 | 3 | 3 |
-DF | Feb. 05 | 2.58 | 2.57 |
-DE | Nov. 04 | 2.57 | 2.57 |
-DE | Sep. 04 | 2.56 | 2.56 |
-CE | Sep. 04 | 2.56 | 2.56 |
-CD | Aug. 04 | 1.63 | 1.6 |
-CD | Jul. 04 | 1.62 | 1.6 |
-CD | Jun. 04 | 1.61 | 1.61 |
-CC | Nov. 04 | 1.6 | 1.6 |
-BC | Sep. 04 | 1.6 | 1.6 |
-BB | Jun. 04 | 1.5 | 1.5 |
-BA | Jun. 04 | 1 | 1 |
-AA | Jun. 03 | 1 | 1 |
PDFsupply Tech
The IC698CPE010 is part of the RX7i family along with IC698CPE020 and IC698CRE020. The IC698CPE010 has processing speed of 300Mhz, which is different than the processing speed of IC698CPE020 and IC698CRE020 which have a 700MHz processing speed.
Common related search terms: BatteryConfiguration, Datasheet, Emerson, Manual, PDF, PLC, Price, Repair, Specification, Troubleshoot, User-Manual, Wiring,
PDF Supply Company, LLC. sells surplus and refurbished products, which are sourced through independent channels. All warranties and support, if applicable, are with PDF Supply Company, LLC. and not the manufacturer; manufacturer warranties do not apply. PDF Supply Company, LLC. is not an authorized distributor or representative for the listed manufacturers and makes no representations as to any quality control performed by any listed manufacturers on the products. The products listed on this website may vary as to their country of origin; the accessories, and other items included with the product; and the language used on the packaging, the parts, and any related instructions or printed material related to the products. PDF Supply Company, LLC. does not sell or license software that may be needed to operate certain hardware and customers must obtain any necessary software licensing, maintenance, or upgrades from the manufacturer or other authorized source. This website is not sanctioned or approved by any manufacturer or other authorized source. This website is not sanctioned or approved by any manufacturer or tradename listed. Designated trademarks, brand names and brands appearing herein are the property of their respective owners.