GE / IP FANUC Series 90/30 In Stock
Preowned
PDF Supply Company, LLC is not an authorized distributor for GE Fanuc Emerson
Other Available Revisions for the IC698ETM001 IC698ETM001-AAIC698ETM001-ABIC698ETM001-ACIC698ETM001-BCIC698ETM001-CDIC698ETM001-CEIC698ETM001-CFIC698ETM001-DGIC698ETM001-DHIC698ETM001-DJIC698ETM001-DKIC698ETM001-EKIC698ETM001-ELIC698ETM001-EMIC698ETM001-ENIC698ETM001-EPIC698ETM001-ERIC698ETM001-ESIC698ETM001-ETIC698ETM001-FEIC698ETM001-FTIC698ETM001-FU
Manufacturer | GE Fanuc |
---|---|
Series | Versamax |
Part Number | IC698ETM001 |
Product Type | Ethernet Interface Module |
Ethernet Processor Speed | 200 MegaHertz |
Operating Voltage | 5 Volts DC |
Current Draw | 1.5 Amps |
Operating Temperature | 0 to 60 degrees Celsius |
Number of IP addresses | 1 |
Ethernet Ports | 2 |
IC698ETM001 is an Ethernet interface module manufactured by GE Fanuc to provide high performance Ethernet communications for RX7i control systems. It has an Ethernet processing speed of 200 MHz. Operating voltage is +5 VDC from the power supply, and current drain is 1.5 (+5 VDC) max. The IC698ETM001 also provides TCP/IP communications with other GE Intelligent Platforms control systems and host computers with software for Ethernet communications to GE Intelligent Platforms controllers.
Select features of IC698ETM001 include provision of full configuration and programming services as well as intermittent data exchange via Ethernet Global Data (EGD). This module offers EGD Class 2 functionality, or commands, and Reliable Data Service (RDS) to ensure command messages are communicated correctly. The module is equipped with comprehensive station management as well as diagnostic tools and extended connectivity. Full-duplex ports provide auto-negotiated network speed and crossover detection due to an internal network switch.
The IC698ETM001 module’s redundant IP addressing permits an individual IP address to be assigned to two Ethernet modules in two different controllers. The address is configured in addition to the original IP address for each interface. The active unit Ethernet interface is the only one that can use the redundant IP. Note: The user must confirm that the gateway IP address is configured.
Flash memory stores protocol in the Ethernet interface and is conveniently upgraded using the CPU serial port. Communications with remote controllers and other nodes are possible via routers. This module is equipped with status LEDs to assist in operation and troubleshooting.
The IC698ETM001 Ethernet Interface Module belongs to the GE Fanuc Versamax family of products. It can be used for providing efficient and high-performance Ethernet communication facilities for the RX7i series control systems. Some of the important features of the module include TCP/IP communication services, SRTP client support, extended connectivity with IEEE and Ethernet LAN ports, programming and configuration services, periodic data exchange, and an EGD Class 2 functionality rating. The IC698ETM001 Ethernet Interface Module comes with 5 LED indicators to indicate the status of the module’s operation and communication. The communication protocol of the Ethernet interface module is stored in flash memory which can be upgraded via the CPU serial port.
The IC698ETM001 Ethernet Interface Module comes with an Ethernet processor speed of 200 Megahertz. Its operating voltage rating is 5 Volts DC and the current draw is 1.5 Amps. This module offers comprehensive station management and diagnostic tools for enhanced performance and easy troubleshooting. Its duplex mode, network speed, and crossover detection features are handled by 2 full-duplex RJ-45 connectors. The mounting method for the module is rack mounting. It allows for the daisy-chaining of Ethernet nodes. The operating temperature range of the IC698ETM001 module is 0 to 60 degrees Celsius. It has 2 auto-sensing shielded Ethernet ports with an 8-pin female, RJ-45 connector. This module can be directly connected to a Base T, twisted pair network hub without an external transceiver. It establishes communication with nodes and remote controllers through the router. The approximate weight of the device is 0.34 kilograms.
Ethernet processor speed |
200 MHz |
Module Operating Voltage |
+5 VDC, (from power supply) |
Module Current Drain |
1.5 (+5 VDC) maximum; 1.2 A typical |
Module Operating Temperature |
0°C to + 60°C (32°F to 140°F) |
LEDs |
MODULE OK LAN ONLINE STATUS 100, LINK P1 100, LINK P2 |
LAN |
IEEE 802.2 Logical Link Control Class I IEEE 802.3 CSMA/CD Medium Access Control 10/100 Mbps |
Number of IP addresses |
One |
Ethernet Ports |
Two, both are 10BaseT / 100BaseTX with auto-sensing. RJ-45 connector, 8-pin female, shielded |
Embedded Ethernet Switch |
Yes – Allows daisy chaining of Ethernet nodes |
Serial Port (Station Mgr Port) |
RS-232 DCE, 1200 - 115200 bps. D-connector, 9-pin female |
Troubleshooting IC698ETM001
Troubleshooting information is available on IC698ETM001's website page; it also includes a datasheet user-manual and a wiring diagram.
Repair your IC698ETM001
PDF Supply can repair your IC698ETM001 in 3-5 business days. And PDF Supply stands by all of its repairs with a 1 year customer satisfaction warranty.
X
Catalog Number |
Date |
Firmware Version |
IC698ETM001-FU |
May 2013 |
6.20 |
IC698ETM001-FT |
Jun. 12 |
6.13 |
IC698ETM001-ET |
Apr. 12 |
6.13 |
IC698ETM001-ES |
Feb. 12 |
6.12 |
IC698ETM001-ER |
Sep. 11 |
6.10 |
IC698ETM001-EP |
Sep. 09 |
6.00 |
IC698ETM001-EN |
Dec. 08 |
5.51 |
IC698ETM001-EM |
May 08 |
5.50 |
IC698ETM001-EL |
Dec. 07 |
5.01 |
IC698ETM001-EK |
Oct. 07 |
5.00 |
IC698ETM001-DK |
Aug. 07 |
5.00 |
IC698ETM001-DJ |
Sep. 06 |
4.00 |
IC698ETM001-DH |
May 06 |
3.81 |
IC698ETM001-DG |
Nov. 05 |
3.60 |
IC698ETM001-CF |
Apr. 05 |
3.00 |
IC698ETM001-N/A |
Nov. 04 |
2.57 |
IC698ETM001-CE |
Jun. 04 |
2.56 |
IC698ETM001-CD |
Apr. 04 |
2.00 |
IC698ETM001-BC |
Mar. 04 |
1.60 |
IC698ETM001-AC |
Dec. 03 |
1.60 |
IC698ETM001-AB |
Sep. 03 |
1.50 |
IC698ETM001-AA |
Jun. 03 |
1.00 |
Common related search terms: ConfigurationDatasheet, Emerson, Manual, PDF, PLC, Price, Repair, Specification, Troubleshoot, User-Manual, Wiring,
PDF Supply Company, LLC. sells surplus and refurbished products, which are sourced through independent channels. All warranties and support, if applicable, are with PDF Supply Company, LLC. and not the manufacturer; manufacturer warranties do not apply. PDF Supply Company, LLC. is not an authorized distributor or representative for the listed manufacturers and makes no representations as to any quality control performed by any listed manufacturers on the products. The products listed on this website may vary as to their country of origin; the accessories, and other items included with the product; and the language used on the packaging, the parts, and any related instructions or printed material related to the products. PDF Supply Company, LLC. does not sell or license software that may be needed to operate certain hardware and customers must obtain any necessary software licensing, maintenance, or upgrades from the manufacturer or other authorized source. This website is not sanctioned or approved by any manufacturer or other authorized source. This website is not sanctioned or approved by any manufacturer or tradename listed. Designated trademarks, brand names and brands appearing herein are the property of their respective owners.