GE / IP FANUC Series 90/30 In Stock
Preowned
PDF Supply Company, LLC is not an authorized distributor for GE Fanuc Emerson
Other Available Revisions for the IC698PSA350 IC698PSA350AIC698PSA350BIC698PSA350CIC698PSA350DIC698PSA350E
Manufacturer | GE Fanuc |
---|---|
Series | RX7i PACSystems |
Part Number | IC698PSA350 |
Product Type | Power Supply Module |
Nominal Rated Voltage | 120/240 Volts AC or 125 Volts DC |
Input Voltage Range | 85 to 264 Volts AC (47 to 63 Hertz) or 100 to 150 Volts DC |
Output Voltage | +5 Volts DC, +12 Volts DC, or -12 Volts DC |
Output Power | 350 Watts |
Maximum Inrush Rating | 60 Amps |
Power Factor | 0.99 |
IC698PSA350 is a PACSystems Power Supply Module produced by GE Fanuc for the RX7i series. This module delivers +5 VDC, +12 VDC, and -12 VDC power. In addition, it sends logic level sequencing signals to modules on the backplane. The module plugs into slot 0 in the main rack.
The IC698PSA350 module’s power supply output may lose one AC input line cycle while maintaining output power. Overcurrent and overvoltage fault protection is provided in addition to electronic short circuit protection. The module permits 100 watts total output power at ambient temperatures of 0 to 60ºC without forced air cooling.
Output voltages are as follows: +5 VDC output to 60 amps, +12 VDC output to 12 amps, and -12 VDC output to 4 amps.
More notable features of the IC698PSA350 module include operation from 85 to 264 VAC or 100 to 150 VDC. The module is equipped with AC operation power factor correction and easy slide-in rack mount construction.
The two-position On/Off logic level switch can be found on the front faceplate. It has the capability to enable or disable output channels and will not disturb the AC line input. Important warning: Lethal voltages are present in the module when input power is present.
Green LED indicators on the IC698PSA350 module monitor the status of field and output. These will turn ON when power is applied within the acceptable range and when DC output channels are operating correctly. A red LED specific to this module will alert the user if critical supply temp is too high or if there is an issue with airflow.
Nominal Rated Voltage: | 120/240 VAC or 125 VDC |
Input Voltage Range: | 85 to 264 VAC or 100 to 150 VDC |
Input Power: | 437 W |
Output Voltages: | + 5 VDC, +12 VDC or -12VDC |
Module Type: | Power Supply |
Rack Location: | Slot 0 (Leftmost slot) |
The GE Fanuc IC698PSA350 Power Supply Module is a DC power supply module that is made for the GE enhanced RX7i PACSystems series control system. This power supply module supplies +5 Volts DC, +12 Volts DC, and -12 Volts DC power and logic-level signals to devices and I/O that are connected to the RX7i backplane. The IC698PSA350 Power Supply Module, like every RX7i series module, has a modular design that allows it to slide perfectly into Slot 0 of the RX7i system’s main rack. The IC698PSA350 Power Supply Module is designed to maintain output power through power losses of up to 1 AC input line cycle, and it comes with built-in over-current, over-voltage, and electronic short-circuit protection. The IC698PSA350 Power Supply Module supports both AC and DC inputs and it has a power factor correction feature for its AC operation.
The IC698PSA350 Power Supply Module has a rated nominal input rating of 120/240 Volts AC or 125 Volts DC, and an acceptable input range of 85 to 264 Volts AC (at 47 to 63 Hertz) or 100 to 150 Volts DC. It has a nominal output power rating of 350 Watts at 60 degrees Celsius and a maximum output value of up to 500 Watts maximum. The IC698PSA350 Power Supply Module has a maximum inrush rating of 30 Amps at 115 Volts AC (cold start) and 60 Amps at 230 Volts AC (cold start) for 100 milliseconds. The IC698PSA350 Power Supply Module has a power factor value of 0.99 that is valid only through 90 to 260 Volts AC and an isolation rating of up to 1500 Volts AC between the input and all outputs for 1 minute. It has an over-voltage output limit of 5.7 to 6.7 Volts DC and an over-current limit of 66 Amps at +5 Volts DC output.
Nominal Rated Voltage: |
120/240 VAC, 125 VDC |
Input Voltage Range: |
85 to 264 VAC 47 to 63 Hz, 100-150VDC |
Input Power 100 W Supply: |
125 watts (typical), 150 watts (maximum) |
Input Power 350 W Supply: |
437 watts (typical), 500 watts (maximum) |
Input Requirements 100W Supply |
|
Inrush current (cold start – 115 VAC) |
15 amps maximum |
Inrush current (cold start – 230 VAC) |
30 amps maximum |
Inrush current duration |
100 milliseconds |
Input Requirements 350W Supply |
|
Inrush current (cold start – 115 VAC) |
30 amps maximum |
Inrush current (cold start – 230 VAC) |
60 amps maximum |
Inrush current duration |
100 milliseconds |
Power Factor |
0.99 min (only valid between 90 VAC and 260 VAC) |
Output Requirements (100 W Supply) |
|
Output Power: |
100 watts maximum (total for all three outputs) |
Output Voltage: |
+5 VDC: 4.875 to 5.25 volts, 0—20 amps |
|
+12 VDC: 11.64 to 12.6 volts,, 0—2 amps |
|
–12 VDC: –12.60 to –11.64 volts, 0—1 amps |
Overvoltage Limit: |
+5 VDC Output: 5.7 to 6.7 volts |
Overcurrent Limit: |
+5 VDC output: 21 A (typical) |
|
+12 VDC output: 2.5 A (typical) |
|
–12 VDC output: 3.5 A (typical) |
Output Requirements (350 W Supply) |
|
Output Power: |
350 watts maximum (total for all 3 outputs) |
Output Voltage: |
+5 VDC: 4.875 to 5.25 volts, 0 to 60 amps |
|
+12 VDC: 11.64 to 12.6 volts, 0 to 12 amps |
|
–12 VDC: –12.6 to –11.64 volts, 0 to 4 amps |
Overvoltage Limit: |
+5 VDC Output: 5.7 to 6.7 volts |
Overcurrent Limit: |
+5 VDC output: 66A (typical) |
+12 VDC output: 15A (typical) |
|
–12 VDC output: 4.6A (typical) |
|
Isolation, input to all outputs |
250 VAC continuous; 1500 VAC for 1 minute |
Protective Limits: Ride-through (time allowed for loss of AC input without affecting DC outputs) Holdup Time (time from ACFAIL# system failure signal is activated to when any DC output drops out of specification) |
15 milliseconds minimum
5 milliseconds minimum |
Operating Temperature: 100W Supply 350W Supply |
0°C to 60°C (32° to 140°F) 0°C to 60°C (32°F to 140°F) Fan tray attachment required for full capacity. See “Ordering Information.” |
Troubleshooting IC698PSA350
Troubleshooting information is available on IC698PSA350's website page; it also includes a datasheet user-manual and a wiring diagram.
Repair your IC698PSA350
PDF Supply can repair your IC698PSA350 in 3-5 business days. And PDF Supply stands by all of its repairs with a 1 year customer satisfaction warranty.
For more information on the IC698PSA350 Multi-Purpose, 120/240 VAC or 125 VDC, 350 Watt Power Supply of the GE Fanuc RX7i Series, please see the Datasheet User-Manual.
Version | Date | Comments |
PSA100E/PSA350E | Aug. 2010 | Label change only. No change in functionality, performance or compatibility. |
PSA100D/PSA350D | Aug. 2006 | Power supplies qualified to the Explosive Atmospheres Directive, European Safety for Hazardous Locations, Equipment Group II, Category 3 (ATEX) agency standard. |
Corrected an infrequently observed issue with power supply shutdown causing corrupted memory faults in CPU. | ||
PSA100C/PSA350C | Jun. 2005 | Overtemperature detection. See GFK-2237C for details. |
PSA100B/PSA350B | May. 2004 | See GFK-2237B for details. |
PSA100A/PSA350A | May. 2003 | Initial release. |
PDFsupply Tech
The IC698PSA350 is part of the RX7i series with an input power of 437 W which is significantly more than the IC698PSA100 which has an input power of 125W.
Common related search terms: DatasheetEmerson, Manual, PDF, PLC, Price, Repair, Specification, Troubleshoot, User-Manual, Wiring,
PDF Supply Company, LLC. sells surplus and refurbished products, which are sourced through independent channels. All warranties and support, if applicable, are with PDF Supply Company, LLC. and not the manufacturer; manufacturer warranties do not apply. PDF Supply Company, LLC. is not an authorized distributor or representative for the listed manufacturers and makes no representations as to any quality control performed by any listed manufacturers on the products. The products listed on this website may vary as to their country of origin; the accessories, and other items included with the product; and the language used on the packaging, the parts, and any related instructions or printed material related to the products. PDF Supply Company, LLC. does not sell or license software that may be needed to operate certain hardware and customers must obtain any necessary software licensing, maintenance, or upgrades from the manufacturer or other authorized source. This website is not sanctioned or approved by any manufacturer or other authorized source. This website is not sanctioned or approved by any manufacturer or tradename listed. Designated trademarks, brand names and brands appearing herein are the property of their respective owners.