GE / IP FANUC Series 90/30 In Stock
Preowned
PDF Supply Company, LLC is not an authorized distributor for GE Fanuc Emerson
Other Available Revisions for the IC693ALG220 IC693ALG220CIC693ALG220-CAIC693ALG220DIC693ALG220FIC693ALG220GIC693ALG220KIC693ALG220-LTIC693ALG220-RR
Manufacturer | GE Fanuc |
---|---|
Series | Series 90-30 |
Part Number | IC693ALG220 |
Product Type | Input Module |
Number of Inputs | 4 |
Module Type | Channel Analog Voltage Input Module |
Compatible Components | PLCs |
Voltage Range | -10 to 10V |
Isolation | 1500V (Between the Field Side and Logic Side) |
Input Filter Response | 17 Hz |
The IC693ALG220 is a Channel Analog Voltage Input module for the Series 90-30. This Programmable Logic Controller delivers four input channels, each able to convert an analog input signal to a digital signal as needed by the user. The module can convert inputs in the range of -10 to +10 volts. Conversion speed for each channel is 1 ms, thus providing an update rate of 4 ms for any channel. Converted signal resolution is 12 bits binary. User data in the %AI registers is in 16-bit 2’s complement format.
This input module is equipped with a limited current input mode and a jumper on the user terminal connector for each channel. The latter can be used to connect the internal 250 ohm shunt resistor to the circuit. The shunt resistor allows a –40 to +40 mA current input range. It is important, however, for the user to monitor input current to avoid self-heating of the input resistor. Otherwise, current accuracy could be negatively affected. The primary power source for the IC693ALG220 comes from the isolated +24 VDC power supplied via the PLC power supply. Voltage is sent through an inverter/regulator to yield operating voltages for the module. The IC693ALG220 uses 27 mA from the +5 VDC output of the PLC power supply.
This module is also equipped with an LED to alert the user regarding operation. This LED is conveniently located near the top of the faceplate. During normal operation, the LED will emit the ON status. Utilizing optical isolation, this module creates electrical isolation of external noise between field wiring and the backplane. To reduce the capacitive loading and noise, it is recommended that the module’s field connections be wired using an appropriate grade of twisted/shielded instrumentation cable.
No. of channels: | 4 Inputs |
Voltage Range: | -10 to +10 volts DC |
Calibration: | Factory calibrated |
Update Rate: | 4 msec |
Input Filter Response: | 17 Hz |
Power Consumption: | 27 mA from +5V bus and 98 mA from +24V bus |
Voltage Range |
–10 to +10 volts t |
Calibration |
Factory calibrated |
Update Rate |
4 msec (all four channels) |
Resolution |
5 mV/20 mA, (1 LSB = 5 mV) |
Absolute Accuracy + |
±10 mV/40 mA (typical) over operating temperature |
|
±30 mV/160 mA (maximum) over operating temperature |
Linearity |
< 1 Least Significant Bit |
Isolation |
1500 volts between field side and logic side |
Cross-Channel Rejection |
> 80 db |
Input Impedance |
> 9 Megohms (voltage mode) |
|
250 ohms (current mode) |
Input Filter Response |
17 Hz |
Internal Power Consumption |
27 mA from +5 volt bus on the backplane |
|
98 mA from the isolated +24 volt backplane bus |
Troubleshooting IC693ALG220
Troubleshooting information is available on IC693ALG220’s website page; it also includes a datasheet user-manual and a wiring diagram.
Repair your IC693ALG220
PDF Supply can repair your IC693ALG220 in 3-5 business days. And PDF Supply stands by all of its repairs with a 1 year customer satisfaction warranty.
IC693ALG390/220 OK LED To Go ON When Installed In RX3i
Description
To have the OK LED to go solid on RX3i; Same modules work on a 90-30 rack
Resolution
These modules require +24V DC power over the backplane. The 90-30 power supply does provide isolated 24VDC power to the serial backplane. The RX3i IC695 Power Supplies do not provide Isolated +24V output power over the backplane. Since the RX3i power supplies do not provide the necessary power over the backplane an external source must be connected. You can bring in the external power and connect to the TB1 input terminals beside the RX3i power supply. See attachment.
· For more information on the IC693ALG220 Analog Input Module of the GE 90-30 Series, please see the Datasheet Manual.
Coming Soon...
Common related search terms: BuyDatasheet, Emerson, Manual, Price, Repair, Specification, Troubleshoot, Wiring,
PDF Supply Company, LLC. sells surplus and refurbished products, which are sourced through independent channels. All warranties and support, if applicable, are with PDF Supply Company, LLC. and not the manufacturer; manufacturer warranties do not apply. PDF Supply Company, LLC. is not an authorized distributor or representative for the listed manufacturers and makes no representations as to any quality control performed by any listed manufacturers on the products. The products listed on this website may vary as to their country of origin; the accessories, and other items included with the product; and the language used on the packaging, the parts, and any related instructions or printed material related to the products. PDF Supply Company, LLC. does not sell or license software that may be needed to operate certain hardware and customers must obtain any necessary software licensing, maintenance, or upgrades from the manufacturer or other authorized source. This website is not sanctioned or approved by any manufacturer or other authorized source. This website is not sanctioned or approved by any manufacturer or tradename listed. Designated trademarks, brand names and brands appearing herein are the property of their respective owners.