GE / IP FANUC Series 90/30 In Stock
SKU 2175421 UPC 0388847101013
All product names, trademarks, brands and logos used on this site are the property of their respective owners. PDF Supply is not an authorized distributor, reseller or representative of the products featured on this website. The depiction, description or sale of products featuring these names, trademarks, brands and logos is for identification purposes only and is not intended to indicate any affiliation with or authorization by any rights holder.
The IC693CPU364 is a single-slot Central Processing Unit (from the GE Fanuc Series 90-30) with an embedded Ethernet cord and 1 built-in serial port. This unit is the "brains" of the PLC and is where most of the calculations take place. See specifications for this unit on IC693CPU364's website page. A standard application for IC693CPU364 would be connecting a computer's 9-pin serial port via IC693CBL316 to IC693CPU364's standard Ethernet interface. It should be noted that IC693CPU364's Ethernet interface is Ethernet Global Data (EGD). The benefit of this built in Ethernet interface is that you do not need to use a separate Ethernet module such as CMM321 with the unit. You can, in fact, save a PLC slot based on the built in nature of an Ethernet port on IC693CPU364.
The EGD also allows CPU364 to handle specialized parameters which HHP's configuration mode is not able to do. Unlike CMM321, CPU364 does not require an external transceiver. CPU364 has a built in transceiver that can be connected to via the 10BASE-T port. CPU364 does offer some added functionality in the ability to add an external transceiver as well though. This can be done via the AAUI port which bypasses the internal transceiver. Another benefit of the built in Ethernet interface is that it can communicate without using the PLC backplane, creating faster communications speed than could be achieved with separate CPU and Ethernet modules. Some basic things to note regarding IC693CPU364 are that when using CPU364 you must connect to frame ground at the slot where it is installed. You can find a grounding wire on the unit for this very use.
CPU364 uses flash firmware standard with no EPROM, and no EEPROM. The current rating on IC693CPU364 is 1A and it uses GE Fanuc Fuse 44A725214–001. The maximum CPU capacity for CPU364 is 25 MHz utilizing the 80386EX processor. There are 2048 input points, 2048 output points. Register memory is configurable from 128 to 32640 words. CPU364 has firmware-based floating point math.
With Firmware Release 9.1 the EGD and configurable Name Resolution features were added to the CPU364.CPU364 has four LED lights, an Ethernet Restart button, a standard CPU keyswitch, three port connectors, and a shield ground connection tab. The four LED indicator lights pertain to the Ethernet interface and the PS port. Three of the lights are for Ethernet: EOK, LAN, and STAT, and 1 is for the PS port. The Ethernet Restart button has four uses:
CPU364 has a Port 1, RS-232, AAUI port, and 10Base T port. These ports allow CPU364 to be connected to a terminal or terminal emulator (PORT 1), connect via IEEE 802.3 to an external Ethernet transceiver (AAUI), and to connect wo a 10Base T Ethernet network.The firmware on CPU364 is, as stated above, stored in Flash memory and loaded via the serial port connector. This is done using a personal computer with loader and software. Similarly, the Ethernet Interface firmware is stored in Flash memory and loaded through the Port 1 connector in the same manner.
The IC693CPU364 is equipped with 8 baseplates, which consist of a single CPU baseplate and 7 baseplates that can either serve as expansion or remote baseplates. It uses an 80386EX processor running at 25 MHz and requires a load of 1.51 amps from +5 VDC power supply. It also has a slow acting, replaceable Ethernet fuse of size 2.69 x 2.69 x 6.1 mm, with a voltage of 125V and a current of 1 A. The module operates with an ambient temperature ranging from 0 to 60 degrees Celsius (or 32 to 140 degrees Fahrenheit). It has a typical scan rate of 0.22 milliseconds per 1K of logic or Boolean contacts.
The IC693CPU364 has up to 240K bytes of program memory available for the user. Please note: the actual size of available user program memory depends on the amounts configured for %R, %AI, and %AQ configurable word memory types as outlined below. Its register memory (%R) is configurable in increments of 128 words, from 128 to 16,384 words with Logicmaster and from 128 to 32,640 words with Control version 2.2. It comes installed with a discrete global memory (%G) of 1280 bits, internal coils (%M) of 4096 bits, output (temporary) coils (%T) of 256 bits, and system status references (%S) of 128 bits (with %S, %SA, %SB, %SC having 32 bits each). Analog inputs (%AI) and outputs (%AQ) are both configurable in increments of 128 words, from 128 to 16,384 words with Logicmaster and from 128 to 32,640 words with Control version 2.2. Discrete input (%I) and output (%Q) outputs are 2,048 each. It has 28 words (%SR) system registers which are used for reference table viewing only and cannot be referenced in user logic program. It supports RAM and flash memory types and has a firmware based floating point math support.
It has shift registers, override, battery-backed clock, with interrupts that support the periodic subroutine feature, and over 2000 timers/counters. It only has one built-in serial port which uses a connector on the PLC power supply. The port supports SNP/SNP-X slave protocols. The module has PCM/CCM compatibility; however, in order to support SNP/SNP-x master, CCM, or RTU slave support, it requires a CMM module. It also requires a PCM module to support RTU master. It has an internal AAUI or 10BASE-T Ethernet (the AAUI requires external transceiver while the 10BASE-T is direct). It also has an additional external Ethernet that supports Ethernet option modules. The installed Local Area Network (LAN) requires option modules for Genius, Profibus, and FIP. Earlier modules may have the LED labeled “SNP” instead of “PS PORT.” Otherwise, these modules are identical.
|Processor Speed:||25 MHz|
|Register Memory:||240 KBytes Total|
|Floating Point Math:||Yes, Firmware Based|
|Load Required||1.1 Amp from +5VDC Supply|
PDF Supply sells used surplus products. PDF Supply is not an authorized distributor, affiliate, or representative for the brands we carry. Products sold by PDF Supply come with PDF Supply’s 1-year, 2-year, or 3-year warranty and do not come with the original manufacturer’s warranty. Designated trademarks, brand names and brands appearing herein are the property of their respective owners. This website is not sanctioned or approved by any manufacturer or tradename listed.
Rockwell Disclaimer: The product is used surplus. PDF Supply is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because PDF Supply is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, PDF Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. PDF Supply also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. PDF Supply also makes no representations as to your right to install any such firmware on the product. PDF Supply will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.