GE / IP FANUC Series 90/30 In Stock
Preowned
PDF Supply Company, LLC is not an authorized distributor for GE Fanuc Emerson
Other Available Revisions for the IC693CPU374 IC693CPU374-ABIC693CPU374-ACIC693CPU374-BDIC693CPU374-BEIC693CPU374-BFIC693CPU374-BGIC693CPU374-BHIC693CPU374-DxIC693CPU374-EKIC693CPU374-ELIC693CPU374-FMIC693CPU374-FNIC693CPU374-GPIC693CPU374-GRIC693CPU374-GSIC693CPU374-GTIC693CPU374-GUIC693CPU374-GVIC693CPU374-HWIC693CPU374-HXIC693CPU374-HYIC693CPU374-JYIC693CPU374-KZIC693CPU374-PlusIC693CPU374-Programming SoftwareIC693CPU374-SoftwareIC693CPU374-CAIC693CPU374-LTIC693CPU374-RR
Manufacturer | GE Fanuc |
---|---|
Series | Series 90-30 |
Part Number | IC693CPU374 |
Product Type | Single-slot CPU with Ethernet controller |
User Memory | 240 KB |
Speed | 10/100 Mbps |
Processor Speed | 133 Mhz |
Temperature | 0-60 degrees Celsius |
Power Rating | 7.4 Watts |
Temperature | 0-60 degrees Celsius |
System Registers | 28 |
Enclosure | Open |
Voltage | 5 Volts DC |
Product Information
The Series 90-30 IC693CPU374 module is a GE Fanuc-manufactured single-slot CPU (AMD SC250) with an embedded Ethernet controller. This CPU 374 module comes with 240 KB of user configurable memory, 4K I/O, and 8 racks. The embedded Ethernet controller supports communication speeds of up to 100 Mbps and it comes with a built-in switch. It supports both SRTP and Ethernet global data along with the Modbus/TCP client/server protocol. No serial ports are present in this module. The processor comes with 133 Mhz of speed with a typical scan rate of 0.15 milliseconds per 1K of logic. It comes with both RAM and Flash memory for storage. The IC693CPU374 module has a power rating of 7.4 Watts and it is supplied with 5 Volts DC voltage. The environmental temperature should be set between 0 and 60 degrees Celsius for operation. When not in use, it can be stored at a temperature between -40 and 85 degrees Celsius.
The GE Fanuc Series 90-30 IC693CPU374 module comes with 2048 fixed discrete input and output points. It has a discrete global memory capacity of 1280 bits. The register memory of the module can be configurable anywhere from 128 to 32640 words. There are 28 fixed system registers present in the CPU with timers and counters. The CPU module is battery backed and it powers the system clock and the RAM. The IC693CPU374 module is equipped with a CPU baseplate and 7 expansion or remote baseplates. The CPU supports different programming languages and it can work with floating point data. It can be configured by using the VersaPro or CIMPLICITY machine edition logic software.
Controller Type |
Single slot CPU module with embedded Ethernet Interface |
Processor |
|
Processor Speed |
133 MHz |
Processor Type |
AMD SC520 |
Execution Time (Boolean Operation) |
0.15 msec per Boolean instruction |
Type of Memory Storage |
RAM and Flash |
Memory |
|
User Memory (total) |
240KB (245,760) Bytes |
Note: Actual size of available user program memory depends on the amounts configured for %R, %AI, and %AQ word memory types. |
|
Discrete Input Points - %I |
2,048 (fixed) |
Discrete Output Points - %Q |
2,048 (fixed) |
Discrete Global Memory - %G |
1,280 bits (fixed) |
Internal Coils - %M |
4,096 bits (fixed) |
Output (Temporary) Coils - %T |
256 bits (fixed) |
System Status References - %S |
128 bits (%S, %SA, %SB, %SC - 32 bits each) (fixed) |
Register Memory - %R |
Configurable 128 to 32,640 words |
Analog Inputs - %AI |
Configurable 128 to 32,640 words |
Analog Outputs - %AQ |
Configurable 128 to 32,640 words |
System Registers - %SR |
28 words (fixed) |
Timers/Counters |
>2,000 (depends on available user memory) |
Hardware Support |
|
Battery Backed Clock |
Yes |
Battery Back Up (Number of months with no power) |
1.2 months for internal battery (installed in the power supply) 15 months with external battery (IC693ACC302) |
Load Required from Power Supply |
7.4 watts of 5VDC. High Capacity power supply required. |
Hand Held Programmer |
CPU374 does not support Hand Held Programmer |
Program Store Devices supported |
PLC Program Download Device (PPDD) and EZ Program Store Device |
Total Baseplates per System |
8 (CPU baseplate + 7 expansion and/or remote) |
Software Support |
|
Interrupt Support |
Supports the periodic subroutine feature. |
Communications and Programmable Coprocessor Compatibility |
Yes |
Override |
Yes |
Floating Point Math |
Yes, hardware floating point math |
Communications Support |
|
Built-in Serial Ports |
No serial ports on CPU374. Supports RS-485 port on power supply. |
Protocol Support |
SNP and SNPX on power supply RS-485 port |
Built-in Ethernet Communications |
Ethernet (built-in) – 10/100 base-T/TX Ethernet Switch |
Number of Ethernet Ports |
Two, both are 10/100baseT/TX ports with auto sensing. RJ-45 connection |
Number of IP Addresses |
One |
Protocols |
SRTP and Ethernet Global Data (EGD) and channels (producer and consumer); Modbus/TCP Client/Server |
EGD Class II Functionality (EGD Commands) |
Supports acknowledged singe command transfers (sometimes referred to as “datagrams”) and Reliable Data Service (RDS – a delivery mechanism to make sure a command message gets through once and only once). |
SRTP Channels |
Up to 16 SRTP Channels Up to 36 SRTP/TCP connections total, consisting of up to 20 SRTP Server connections and up to 16 Client Channels. |
Web Server Support |
Provides basic Reference Table, PLC Fault Table, and IO Fault Table data monitoring over the Ethernet network from a standard web browser |
Need more help?
Email us at sales@pdfsuply.com or Request a Formal Quote for IC693CPU374
All orders placed Monday - Friday before 3:30pm EST will be shipped same day.
Free UPS Ground Shipping!
Troubleshooting IC693CPU374: |
Troubleshooting information is available on IC693CPU374's website page; |
it also includes a datasheet user-manual and a wiring |
Repair your IC693CPU374: |
PDF Supply can repair your IC693CPU374 in 3-5 business days. |
And PDF Supply stands by all of its repairs with a 1 year customer satisfaction warranty. |
Missing Web and FTP Components |
Description: |
This is for IC693CPU374 PLUS, only. |
If you do not have these components in Proficy Machine Edition project: |
Under the Ethernet TAB, for your CPU |
Max number of web server connections - Missing |
Max number of FTP server connections - Missing |
the version of VersaPro 2.04 or less. |
This functionality is not supported in VersaPro. OR You are working with a project that was imported from a VersaPro Configuration. |
Resolution: |
For this functionality, create the project in Machine Edition 5.5. |
OR Note the CPU configuration. In Machine Edition 5.5, remove the CPU from the Hardware Config, add the CPU to the hardware config. |
Reasons Why Modbus TCP Client Does Not Work for 90-30 CPU374 |
Description: |
Common items to check before implementing Modbus TCP Client for 90-30 CPU374 |
: Ensure CPU374 firmware is at 12.10 or later. Release 12.10 firmware added support for Modbus TCP Client. |
Proficy Machine Edition used to configure the PLC must be at version 5.60 SIM9 or later. |
Common Problem: |
" Upgraded CPU374 firmware to 12.10 (or later) and have updated |
Machine Edition to 5.60 SIM9 (or later), but Modbus TCP Client still does not work. Why? " |
If the PLC project was created with a version prior to 5.60 SIM9, the CPU374 in the hardware configuration |
must be replaced and added in again as it won't have the "Modbus TCP Address Map" tab in the configuration parameters.; |
Restoring a project (created before 5.60 SIM9) in 5.60 SIM9 or later won't enable the Modbus TCP Map tab, |
the module must be replaced and added in again by right clicking on the CPU module and choosing "Replace Module" and selecting IC693CPU374. |
See attached which shows how the CPU374 configuration appears in a project created before 5.60 SIM9 and one created with 5.60 SIM9 or later. |
Series 90-30 WEB Enabled CPU374 Plu |
Description: |
The firmware revision D (IC693CPU374-Dx) and earlier are not compatible with WEB enabled CPU374 Plus. |
Firmware updates are not compatible with the D revision or earlier versions. |
The CPU374 revision E (IC693CPU374-Ex) and later are the enabled Plus versions |
Resolution |
Differences between New CPU374 Plus and existing CPU374 |
New Ethernet microprocessor with improved multicast data filtering for applications that have excessive network traffic |
Support Channels (Producer and Consumer), EGD (Modbus TCP is a future release) |
Supports PLC data monitoring over the web. Allows a combined total of up to 16 web server and FTP connections. |
Web pages that display Reference Table data, PLC Fault Table contents, and IO Fault Table contents. |
Need more help?
Email us at sales@pdfsuply.com or Request a Formal Quote for IC693CPU374
All orders placed Monday - Friday before 3:30pm EST will be shipped same day.
Free UPS Ground Shipping!
Customer Questions and Answers |
Question: What is an IC693CPU374? |
Answer: The IC693CPU374 is a single-slot Central Processing Unit with an embedded Ethernet Interface. |
This unit is the "brains" of the PLC and is where most of the calculations take place. |
Question: What is the processor speed for IC693CPU374? |
Answer: 133 MHz |
Question: What is the total user memory for IC693CPU374? |
Answer: 120Kz |
Question: Is there anything recommended for this processor? |
Answer: Yes, because the built-in battery is limited to 1.2 months of continuous power outage, |
an IC693ACC302 external battery is recommended. |
Question: Are there built-in Ethernet ports on IC693CPU374? |
Answer: Yes. (2) RJ-45 |
Question: Does IC693CPU374 support the Hand Held Programmer? |
Answer: No. |
Question: What power supply does IC693CPU374 require? |
Answer: IC693CPU372 requires a high capacity power supply. |
Question: What should I do if my IC693CPU374 is not working? |
*For more information on the IC693CPU374 Central Processing Unit of the GE 90-30 Series, please see the Datasheet Manual.
Need more help?
Email us at sales@pdfsuply.com or Request a Formal Quote for IC693CPU374
All orders placed Monday - Friday before 3:30pm EST will be shipped same day.
Free UPS Ground Shipping!
CPU374 PLUS Release History |
|||
Revision |
Firmware Versions |
Date |
|
CPU |
Ethernet |
||
CPU374-KZ |
12.71 |
6.2 |
Jul. 2013 |
CPU374-JY |
12.71 |
6.13 |
May 2012 |
CPU374-HY |
12.71 |
6.13 |
Apr 2012 |
CPU374-HX |
12.71 |
6.12 |
Feb 2012 |
CPU374-HW |
12.5 |
4.52 |
Oct 2011 |
CPU374-GV |
12.22 |
4.52 |
Mar 2010 |
CPU374-GU |
12.21 |
4.52 |
Sep 2009 |
CPU374-GT |
12.17 |
4.52 |
May 2009 |
CPU374-GS |
12.16 |
4.51 |
Jan 2008 |
CPU374-GR |
12.1 |
4.5 |
Jul 2007 |
CPU374-GP |
12.04 |
3.32 |
Apr 2006 |
CPU374-FN |
12.03 |
3.31 |
Dec 2005 |
CPU374-FM |
12.02 |
3.31 |
Nov 2005 |
CPU374-EL |
12 |
3.3 |
Sep 2005 |
CPU374-EK |
12 |
3.3 |
Jun 2005 |
Need more help?
Email us at sales@pdfsuply.com or Request a Formal Quote for IC693CPU374
All orders placed Monday - Friday before 3:30pm EST will be shipped same day.
Free UPS Ground Shipping!
PDFsupply Tech
The IC693CPU374 GE Fanuc CPU module has a processing speed of 133 MHz which much higher than the IC693CPU363, which has a processing speed of only 25 MHz. This GE Fanuc processor also has 240 KB of user memory.
Common related search terms: BatteryBuy, Configuration, Datasheet, Emerson, Firmware, Manual, Price, Repair, Specification, Troubleshoot, Wiring,
PDF Supply Company, LLC. sells surplus and refurbished products, which are sourced through independent channels. All warranties and support, if applicable, are with PDF Supply Company, LLC. and not the manufacturer; manufacturer warranties do not apply. PDF Supply Company, LLC. is not an authorized distributor or representative for the listed manufacturers and makes no representations as to any quality control performed by any listed manufacturers on the products. The products listed on this website may vary as to their country of origin; the accessories, and other items included with the product; and the language used on the packaging, the parts, and any related instructions or printed material related to the products. PDF Supply Company, LLC. does not sell or license software that may be needed to operate certain hardware and customers must obtain any necessary software licensing, maintenance, or upgrades from the manufacturer or other authorized source. This website is not sanctioned or approved by any manufacturer or other authorized source. This website is not sanctioned or approved by any manufacturer or tradename listed. Designated trademarks, brand names and brands appearing herein are the property of their respective owners.