GE / IP FANUC Series 90/30 In Stock

World's Largest Warehouse

of GE 90-30, Genius, and RX7i

Mon-Fri 8AM-5PM EST



Rated 4.1/5 Based on 15 ratings.

Rate your purchase of the IC693MDL330

SKU 2176450  UPC 0611384287323

All product names, trademarks, brands and logos used on this site are the property of their respective owners. PDF Supply is not an authorized distributor, reseller or representative of the products featured on this website. The depiction, description or sale of products featuring these names, trademarks, brands and logos is for identification purposes only and is not intended to in indicate any affiliation with or authorization by any rights holder.

PDF Supply is NOT an authorized distributor for this manufacturer and therefore the manufacturer’s warranty does not apply. Product comes with PDF Supply's 1-year, 2-year, or 3-year warranty.

Common misspellings:
  • 1C693MDL330
  • IC693MD1330
  • IC693MDL33o
  • IC693MDL330

Technical Specifications for IC693MDL330

ManufacturerGE Fanuc
SeriesSeries 90-30
Part NumberIC693MDL330
Product TypeInput Module
Power TypeAC
Output Voltage Range85-264V AC
Number of Input Points8
Load Current per Point1 A
Output TypeTriac

Product Description

IC693MDL330 is a 120/240 volt, 2-Amp AC Output Module for the GE Fanuc Series 90-30. The module provides four output points in each of its two isolated groups for a total of eight. The two commons are not compound for this module. This allows each group to perform on completely individual AC-supplied phases. Alternatively, they can all also work using the same supply. Each group also has the protection of a 5-ampere fuse for each common. There is an RC snubber in place for each output to protect against transient electrical noise on the power line.

The output voltage range for this module is 85 to 264 volts AC, 50/60 Hz. The output current is 2 amperes maximum per point. Per group, the maximum is 4 amps at 40 °C (104 °F). The IC693MDL330 provides high-degree inrush current (10x the rated current/ 20 amperes maximum for one cycle), making the outputs suitable for controlling a wide range of inductive and incandescent loads. The minimum load current is 100 mA.

The user must provide AC Power for operating loads connected to outputs. DC is not supported. The IC693MDL330 module has LED indicators at the top, which display the ON/OFF status for each point. There are two horizontal rows with eight green LEDs each, as well as one LED at the center between the two rows. The eight upper LEDs, which are labeled A1 through 8, indicate output status. The red “F” LED indicates a blown fuse, showing ON if this happens. The IC693MDL330 has an insert between the inside and outside surface of the hinged door. When the hinged door is closed, the surface facing the inside of the module displays circuit wiring information, and circuit identification information can be recorded on the external surface. The external left edge of the insert is color-coded red to indicate a high-voltage module. The IC693MDL330 has an ON response time of 1 ms maximum, while the OFF response time is ½ cycle maximum. Its power consumption is of 160 mA (with all outputs on) from 5 voltages bus on backplane.

Technical Specifications

Rated Voltage: 120/240 volts AC
# of Inputs: 8
Freq: 50/60 Hz
Output Current: 2.0 A per point
Output Voltage Range:   85 - 132 volts AC
DC Power: No


The GE Fanuc IC693MDL330 module is an input module that provides an interface between a PLC and different external input devices that are necessary for an application process. This module is part of Series 90-30 by GE Fanuc Automation. Some of the external input devices compatible with this module are proximity sensors, pushbuttons, switches, and BCD thumbwheels, among others. This input module operates with an AC voltage of 120 to 240 Volts AC and a current rating of 1 Amp. The output voltage range of the module goes from 85 to 264 Volts AC and it comes with 8 input points. The GE Fanuc Automation IC693MDL330 input module does not provide any kind of isolation and its load current per point is 1 Amp. This module comes with a response time of 1 millisecond.

The GE Fanuc Automation Series 90-30 IC693MDL330 input module comes with a Triac output type and it does not include any kind of polarity for this output type. This module comes with 4 input points per common group for a total of 8 input points and it comes with a terminal connector that ships with it. The GE Fanuc Automation IC693MDL330 input module operates with an internal power consumption rating of 160 milliamps at 5 Volts DC. Before attempting to install or acquire this module, the users must ensure that it is fully compatible with the ratings of the application and the machine where it will be installed. The same inspection needs to be done with all the output devices that are going to be interfaced through this module.

Technical Information


Rated Voltage

120/240 volts AC

Output Voltage Range

85 to 264 volts AC, 50/60 Hz

Outputs per Module

8 (two groups of four outputs each)


1500 volts between field side and logic side


500 volts between each group

Output Current t

2 amp maximum per point

4 amps maximum per group at 40 ° C (104°F)

Output Characteristics


Inrush Current

20 amps maximum for one cycle

Minimum Load Current

100 mA

Output Voltage Drop

1.5 volts maximum

Output Leakage Current

3 mA maximum at 120 volts AC


6 mA maximum at 240 volts AC

On Response Time

1 ms maximum

Off Response Time

1/2 cycle maximum

Power Consumption

160 mA (all outputs on) from 5 volt bus on backplane


Troubleshooting IC693MDL330

Troubleshooting information is available on IC693MDL330’s website page; it also includes a datasheet user-manual and a wiring diagram.  


Repair your IC693MDL330

PDF Supply can repair your IC693MDL330 in 3-5 business days. And PDF Supply stands by all of its repairs with a 1 year customer satisfaction warranty.


Customer Questions and Answers

  • Question:  What is an IC693MDL330?  Answer:  The IC693MDL330 is a 120/240 volt, 2 Amp AC Output module for the GE Fanuc Series 90-30. It provides 8 output points in 2 isolated groups with 4 points in each group. The 2 commons are not tied together inside the module. This allows each group to be used on different phases of the AC supply or they can be powered from the same supply. 
  • Question:  What is the rated voltage of IC6963MDL330?  Answer:  120/240 volts AC
  • Question:  What is the output voltage range of IC693MDL330?  Answer:  85 to 264 volts AC, 50/60 Hz
  • Question:  What kind of power source does this module require?  Answer:  The IC693MDL330 requires an AC power source. A DC power source cannot be used with this module.
  • Question:  With what is each group protected?  Answer:  A 5 amp fuse. A RC snubber is also there for each output to protect from transient electrical noise on the power line.
  • Question:  Into what can the IC693MDL330 be installed?  Answer:  The IC693MDL330 can be installed in any I/O slot of a 5 or 10 baseplate in a Series 90-30 PLC system.
  • Question:  What does the red LED (labeled F) mean if it turns ON?  Answer:  It means that one of the fuses has blown. 
  • Question:  What should I do if my IC693MDL330 is not working properly?  Answer:  If your IC693MDL330 is not correctly working, then your product may need repair.

For more information on the IC693MDL330 AC Output Module of the GE 90-30 Series, please see the Datasheet Manual.


ST. LOUIS, Feb. 1, 2019 – Emerson today announced it has completed the purchase of Intelligent Platforms from General Electric.

Common related search terms: BuyDatasheetEmersonManualPriceRepairSpecificationTroubleshootWiring


PDF Supply sells used surplus products. PDF Supply is not an authorized distributor, affiliate, or representative for the brands we carry. Products sold by PDF Supply come with PDF Supply’s 1-year, 2-year, or 3-year warranty and do not come with the original manufacturer’s warranty. Designated trademarks, brand names and brands appearing herein are the property of their respective owners. This website is not sanctioned or approved by any manufacturer or tradename listed.

Rockwell Disclaimer: The product is used surplus. PDF Supply is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because PDF Supply is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, PDF Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. PDF Supply also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. PDF Supply also makes no representations as to your right to install any such firmware on the product. PDF Supply will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.