PDF Electric and Supply

1-800-360-6802
1-919-535-3180
sales@pdfsupply.com

IC693MDL340

Buy NowIC693MDL340
IC693MDL340
IC693MDL340 Wiring

Rated 4.7/5 based on 23 ratings.
  • IC693MDL340
  • IC693MDL340 Wiring

Product Description


The IC693MDL340 is a 120 volt, 0.5 Amp AC Output Module of the Series 90-30 manufactured by GE Fanuc. It provides 16 output points in two isolated groups with eight points in each. Each of these groups has a separate common associated with it (the two commons are not integrated inside the IC693MDL340), allowing each group to be used with independent AC supply phases. Alternatively, it is also possible to power both commons with the same supply. Each group has a 3-ampere fuse for protection, as well as an RC snubber for each output to guard them against transient electrical noise from the power line. This module also has an output voltage range of 85 to 132 volts AC, 50/60 Hz, and an output current of 0.5 amperes maximum per point. The maximum per group is 3 amps.

IC693MDL340 provides a high-degree of inrush current, making its outputs advisable for controlling a great variety of loads, both inductive and incandescent. The user must provide an AC Power supply to operate the loads connected to outputs. This module can only function on an AC power source. IC693MDL340 has LED signaling lights at the top, designed to represent the ON/OFF status for each point. Additionally, it also has two horizontal lines with another eight green LEDs each, and one final LED at the center between the two lines. The eight LEDs at the top, which are identified as A1 to 8, indicate output status. The red “F” LED turns on to signal a blown fuse. Unless there is a load connected to the blown fuse, the LED will not function.

IC693MDL340 features an insert that separates its hinged door’s external and internal surface. Once this door is closed, circuit wiring information is shown the inside surface of the module, and circuit identification information can be found on the outside surface. The external left edge of the insert is colored red to indicate a high-voltage module. IC693MDL340 module can be installed in any I/O slot of a 5 or 10-slot baseplate in a Series 90-30 PLC system. IC693MDL340 has a response time of 1 ms maximum when ON and a maximum off response time of ½ cycle. It has a power consumption of 315 mA (when all outputs are on) from 5 voltages bus on backplane.

Technical Specifications


Rated Voltage:  120 volts AC
# of Outputs: 16
Freq: 50/60 Hz
Output Current:  0.5 A per point
Output Voltage Range:    85 - 132 volts AC
DC Power: No

 

 

GE Intelligent Platforms / GE Fanuc GE Series 90-30

SKU 2177115  UPC 0135686018275

Part Number: IC693MDL340 / ic693mdl340
Mfr/Brand Name: GE Automation
Mfr Number: IC693MDL340 / ic693mdl340
Type: 120 volt AC Output Module, 16 output points.

Technical Specifications

  • 0.5 Amp
    Troubleshooting and Product Information for IC693MDL340

    Download product information, troubleshooting guides and operation manuals to get your PLC operational.

    New IC693MDL340
    Price: $1,195
    45 In Stock
    1 Year Warranty

    *Need a Specific Revision?

    New Surplus IC693MDL340
    Price: $895
    3 In Stock
    3 Year PDF Supply Warranty

    *What is New Surplus?

    Save
     26%
    Reman IC693MDL340
    Price: $225
    2
    In Stock

    2 Year PDF Supply Warranty

    *What is Remanufactured?

    Save
     82%
    Repair Your IC693MDL340
    Price: $166
    1 Year PDF Supply Warranty
    Call For Assistance
    1-800-360-6802

    Other IC693MDL340

    Available Revisions:

    Confirm Your Revision Number

    1C693MDL340 , GEFIC693MDL340 , CIMIC693MDL340

     

    Rated Voltage

    120 volts AC

    85 to 132 volts AC, 50/60 Hz

    16 (two groups of eight outputs each)

    1500 volts between field side and logic side 500 volts between each group

    0.5 amp maximum per point 3 amps maximum per group

     

    20 amps maximum for one cycle 50 mA

    1.5 volts maximum

    2 mA maximum at 120 volts AC 1 ms maximum

    1/2 cycle maximum

    315 mA (all outputs ON) from 5 volt bus on backplane

    Output Voltage Range

    Outputs per Module

    Isolation

    Output Current

    Output Characteristics

    Inrush Current

    Minimum Load Current

    Output Voltage Drop

    Output Leakage Current

    On Response Time

    Off Response Time

    Power Consumption

    Troubleshooting IC693MDL340

    Troubleshooting information is available on IC693MDL340’s website page; it also includes a datasheet user-manual and a wiring diagram.  

     

    Repair your IC693MDL340

    PDF Supply can repair your IC693MDL340 in 3-5 business days. And PDF Supply stands by all of its repairs with a 1 year customer satisfaction warranty.

     

    IC693MDL340 - Replacing The Fuse When "F" Fuse LED is "ON"

    Description

    120 V ac output - 0.5 Amp, 16 Point - IC693MDL340 - Replace fuses when "F" Fuse LED is "ON"

    Resolution

    The 120 V, 0.5 A ac output module provides 16 output points in two isolated groups with eight points in each group. Each group has a separate common associated with it (two commons are not tied together inside the module). This allows each group to be used on different phases of ac supply or they can be powered from the same supply. Each group is protected with a 3 A fuse, and a RC snubber is provided for each output to protect against transient electrical noise on the power line. This module provides a high-degree of inrush current which makes the outputs suitable for controlling a wide range of inductive and incandescent loads. AC Power to operate loads connected to outputs must be supplied by the user. This module requires an AC power source. LED indicators which provide the ON/OFF status of each point are located at the top of the module. There are two horizontal rows with eight green LEDs in each row and a red LED centered between and to the right of the two rows. This module uses the two rows of green LEDs, labeled A1 through 8 and B1 through 8 for output status. The red LED (labeled F) is a blown fuse indicator that turns ON if either of the fuses should blow. A load must be connected to the blown fuse for the indicator to light. An insert goes between the inside and outside surface of the hinged door. The surface towards the inside of the module (when the hinged door is closed) has circuit wiring information, and circuit identification information can be recorded on the outside surface. The outside left edge of the insert is color-coded red to indicate a high-voltage module. This module can be installed in any I/O slot of a 5 or 10-slot baseplate in a Series 90-30 PLC system.

    Refer to the attached picture for the location of the fuses on the circuit board. Access the fuses after removing the plastic cover by opening the transparent front face. The front transparent cover over the front LEDs. Remove the terminal strip 2 clips on the right side and the one under.

     

    Customer Questions and Answers


    • Question:  What is an IC693MDL340?  Answer:  The IC693MDL340 is a 120 volt, 0.5 Amp AC Output module in the GE Fanuc 90-30 Series. This module provides 16 output points in 2 isolated groups with 8 points in each group. Each of these groups has an individual common related to it. The 2 commons are not joined together in this module. Which means that each group can function on different phases of the AC supply or it can function from the same supply. 
    • Question:  What is the rated voltage of IC6963MDL340?   Answer:  120 volts AC
    • Question:  What is the output voltage range of IC693MDL340?   Answer:  85 to 132 volts AC, 50/60 Hz
    • Question:  What kind of power source does this module require?   Answer:  The IC693MDL340 requires an AC power source.
    • Question:  With what is each group protected?   Answer:   3 amp fuse. A RC snubber is also there for each output to protect from transient electrical noise.
    • Question:  Into what can the IC693MDL340 be installed?   Answer:  The IC693MDL340 can be installed in any I/O slot of a 5 or 10 baseplate in a Series 90-30 PLC system.
    • Question:  What does the red LED (labeled F) mean if it turns ON?   Answer:  It means that one of the fuses has blown. 
    • Question:  What should I do if my IC693MDL340 is not working properly?   Answer:  If your IC693MDL340 is not correctly working, then your product may need repair.

    For more information on the IC693MDL340 AC Output Module of the GE 90-30 Series, please see the Datasheet Manual.

     

    Need To Order A Specific Revision?

    Give us a call at 1-800-360-6802 or 1-919-535-3180.

    We can help you with your Revision specific needs.


    Free Overnight delivery on orders over $500!

    What is New Surplus?

    These “New Surplus” units are a great cost saving alternative. This product is sealed in the original manufacturer’s packaging with all sub-assemblies and documentation. May indicate older date code. Comes with a PDF Supply 3-year warranty.


    Free Overnight delivery on orders over $500!


    What is Surplus New?

    Surplus New - New unused and includes all sub-assemblies and documentation. Product may ship in manufacturer or PDF Supply packaging. May indicate older date code. Includes a PDF Supply 3 Year Warranty.


    Free Overnight delivery on orders over $500!


    What is Reconditioned?

    Reconditioned products from PDF Supply are a cost-effective alternative to new and obsoleted PLC products. Every part is reconditioned down to the circuit board level and updated to the latest revision. All parts are thoroughly inspected and hand-cleaned before being functionally tested in a fully configured system.


    Our Reconditioned Products always come with a PDF Supply 2-Year Warranty.

    Free Overnight delivery on orders over $500!


    What is a Verified Substitute?

    A verified substitute new product is a "drop in" replacement designed with identical specifications as the OEM product. It will meet all electrical and dimensional charactertics at a substanstially reduced price.


    Free Overnight delivery on orders over $500!


    Download Lastest Documentation


    Please visit this manufacturer's website to download the lastest manuals and datasheets.


    Lowest Price Guarantee


    We stand behind our prices with a lowest price guarantee. If you find a legacy GE PLC part advertised for less on an authorized GE PLC distributor website, simply contact us and send us a link to the lower advertised price. We will match that price and ship overnight FREE. The item must be in stock, in similar condition and be able to ship same day.

    Free Shipping



    FREE Overnight Delivery for Continental US orders over $500!

    FREE Ground Delivery for Continental US orders under $500!

    US orders placed Monday - Friday before 5pm EST will ship same day.

    Canada/Mexico orders placed Monday - Friday before 3:30pm EST will ship same day.

    International orders will ship the following business day.