GE / IP FANUC Series 90/30 In Stock
SKU 2171209 UPC 0553640565557
All product names, trademarks, brands and logos used on this site are the property of their respective owners. PDF Supply is not an authorized distributor, reseller or representative of the products featured on this website. The depiction, description or sale of products featuring these names, trademarks, brands and logos is for identification purposes only and is not intended to indicate any affiliation with or authorization by any rights holder.
The 5/24-volt DC (TTL) Negative Logic Output module, IC693MDL752, has 32 negative logic or sinking type output points (active low) and uses 32 bits of discrete %Q output data. The outputs are arranged in four separate groups (labeled A to D), each group comprised of eight outputs each (numbered 1 to 8) with each group having its unique common. It can be installed in any Series 90-30 Programmable Logic Controller (PLC) system having a 5 or 10- I/O slot baseplate. Each group common has user I/O connectors which carry two pins. Each pin on these connectors has a current handling capacity of 3 amperes. Making connections to both pins is recommended when connecting the common, but required for applications requiring high current such as between 3 and 4 amperes.
The IC693MDL752 operates in two modes: Transistor-Transistor Logic (TTL) and 12/24V modes. In the TTL mode, each output can switch user loads across +5 VDC. In 12/24V mode, user loads can be switched in the range of +12 to -24 VDC. Also, output points, in each mode (TTL and 12/24V), can sink a maximum current of 25 mA and 0.5A per point respectively. Each output group in the module (A to D) can be utilized in the operating mode that is appropriate for the load requirements of a specific task or application. Group A can be applied to TTL load tasks and Group B to 12 VDC loads, while the Groups C and D can be applied to 24 VDC load tasks. However, when mixing modes (TTL and inductive-type loads), as in this regard, it is important to take cognizance of electrical noise and its effects.
User load devices are connected to the module through two male 24-pin connectors that are located on the front of the module. The connectors on the right interfaces with groups A and B output points while those on the left interfaces with groups C and D output points. Optocouplers on the module provide backplane isolation between the field side and logic side. The module also has LED indicators, labeled correspondingly to each output, at the top of the module which indicates the active (ON) or inactive (OFF) status of each output point. There is no reporting of special fault or alarm diagnostics.
Each output point has an internal pull-up resistor. When the output point's field-effect transistor (FET) is off, the resistor aims at providing a high logic level for TTL tasks. It does this by pulling up the output to the positive side of the user power input, which, for TTL tasks, is typically +5V. Stopping the CPU forces all 32 output points off and the user must provide power to supply current to the loads. A minimum amount of the user-supplied power is used by the module to provide gate drive to output devices.
|Rated Voltage:||5 and 12 thru 24 volts DC|
|# of Outputs:||32|
|Output Current:||25 mA per point (TTL mode)|
|Output Voltage Range:||4.75 to 5.25 volts DC (TTL mode)|
5/12/24 Volts dc (TTL) Output, Neg Logic, (32) IC693M IC693MD IC693MDL
PDF Supply Company, LLC. sells surplus and refurbished products, which are sourced through independent channels. All warranties and support, if applicable, are with PDF Supply Company, LLC. and not the manufacturer; manufacturer warranties do not apply. PDF Supply Company, LLC. is not an authorized distributor or representative for the listed manufacturers and makes no representations as to any quality control performed by any listed manufacturers on the products. The products listed on this website may vary as to their country of origin; the accessories, and other items included with the product; and the language used on the packaging, the parts, and any related instructions or printed material related to the products. PDF Supply Company, LLC. does not sell or license software that may be needed to operate certain hardware and customers must obtain any necessary software licensing, maintenance, or upgrades from the manufacturer or other authorized source. This website is not sanctioned or approved by any manufacturer or other authorized source. This website is not sanctioned or approved by any manufacturer or tradename listed. Designated trademarks, brand names and brands appearing herein are the property of their respective owners.