GE / IP FANUC Series 90/30 In Stock
Other Available Revisions for the IC693MDL754 IC693MDL754/-AIC693MDL754/-ABIC693MDL754/-BCIC693MDL754/-CCIC693MDL754/-CDIC693MDL754/-DDIC693MDL754/CAIC693MDL754/LTIC693MDL754/RR
Manufacturer | GE Fanuc |
---|---|
Series | Series 90-30 |
Part Number | IC693MDL754 |
Product Type | Output Module |
Compatible With | GE Fanuc 90-30 PLCs |
Output Points | 32 |
Output Groups | 2 |
Output Point Peak Current | 0.75 Amps |
Module Current Draw | 300 milliamps |
Module Voltage Input | 5 Volts DC |
The GE Fanuc IC693MDL754 is a positive logic output module. It is available with a voltage rate of 12/24 V from a DC supply. Each module comes with 32 output points. These points groups into two separate 16 output points. Each group finds its utilization for driving different loads. If one group drives a 12V load from DC supply, then the other group will drive the 24V load. The output current from this module is 0.75 A per each point. This module also consumes the power of 300 mA from 5V bus situated on its backplane. The IC693MDL754 has an auto-recovery feature. This feature gives protection to the module against the short circuit, over temperature, and current.
The IC693MDL754 module has 32 yellow/green LEDs. They indicate the switching status of each output point. Green LEDs indicate that the output points are switched on. Otherwise, if the output points have an off status, then there are no indications from the LEDs. Yellow LEDs indicate whenever there is a fault in the output points. The IC693MDL754 module consists of a DIP switch. They are located on its rear end. The DIP switch carries out the default operation for its output circuits. Also, this module can send 16 bits status data into the CPU. The load 30V DC causes the start of thermal de-rating of the output. At an ambient temperature above 42°C, the output of this module is de-rated. The response time for switching on and off of the module is 0.5 msec.
Rated Voltage: | 12/24 volts DC |
# of Outputs: | 32 |
Freq: | n/a |
Output Current: | 0.75 A per point with ESCP |
Output Voltage Range: | 12 to 24 volts DC (+20%, -15%) |
DC Power: | Yes |
Specifications
Outputs per Module |
32 (two isolated groups of 16 outputs each) |
Rated Voltage Output Voltage Range |
12/24 volts DC, nominal 10.2 to 30 volts DC |
Field to Backplane (optical) and to Frame Ground |
250 VAC continuous; 1500 VAC for 1 minute |
Group to Group |
250 VAC continuous; 1500 VAC for 1 minute |
Board ID |
With Module Diagnostics enabled: 0x1A With Module Diagnostics disabled: 0x0E |
Output Current |
0.75 Amps per point |
Power Consumption |
300 mA (maximum) from 5 volt bus on backplane; |
Thermal Derating |
No derating at 24VDC. At 30VDC, outputs are derated above 42°C as shown below. |
External Power Supply |
|
Rated Voltage |
+12 VDC to +30 VDC, 12/24 VDC nominal Requires isolation that is provided by means such as a transformer. |
External Power Supply Current Required (not including load current) |
Module version –CC and later: 72 mA/group with all outputs commanded Off, 132 mA/group with all outputs commanded ON |
|
Module version –BC and earlier: 72 mA/group with all outputs commanded OFF, 100 mA/group with all outputs commanded ON |
Output Characteristics |
|
Output Voltage Drop |
0.3 volt DC maximum |
Inrush Current |
3 Amps supplied for 10ms, without ESCP trip |
Steady-state overcurrent trip |
5 Amps typical per point |
Output Leakage Current |
0.1mA maximum |
On Response Time |
0.5ms maximum |
Off Response Time |
0.5ms maximum |
Protection |
Short-circuit protection, overcurrent protection, overtemperature protection, all with auto recovery. |
Troubleshooting IC693MDL754
Troubleshooting information is available on IC693MDL754’s website page; it also includes a datasheet user-manual and a wiring diagram.
Repair your IC693MDL754
PDF Supply can repair your IC693MDL754 in 3-5 business days. And PDF Supply stands by all of its repairs with a 1 year customer satisfaction warranty.
For more information on the IC693MDL754 DC Positive Logic ESCP Output Module of the GE 90-30 Series, please see the Datasheet Manual.
Release |
Date |
Comments |
IC693MDL754-DD |
Jan 2016 |
Change in fab color. No change in form-fit-functionality. |
IC693MDL754-CD |
Mar 2009 |
Resolved Hold Last State issue. |
IC693MDL754-CC |
Jun 2008 |
The module no longer becomes inoperable after a period of many rapidly- repeated power cycles. For RX3i, hot insertions that take longer than 1 second no longer cause a System Configuration Mismatch fault. |
IC693MDL754-BC |
Nov 2005 |
The module no longer becomes inoperable after a period of many rapidly-repeated power cycles. For RX3i, hot insertions that take longer than 1 second no longer cause a System Configuration Mismatch fault. |
IC693MDL754-AB |
Oct 2005 |
Fault displayed if module firmware is missing or corrupted. |
IC693MDL754-A |
Mar 2005 |
Initial Release |
Common related search terms: BuyDatasheet, Emerson, Manual, Price, Repair, Specification, Troubleshoot, Wiring,
PDF Electric & Supply Inc. sells new, new surplus and refurbished products which are sourced through independent channels. All warranties and support, if applicable, are with PDF Electric & Supply Inc. and not the manufacturer. PDF Electric & Supply Inc. is not an authorized distributor or representative for the listed manufacturers and makes no representations as to any quality control performed by any listed manufacturer on the products. The products listed on this website may vary as to their country of origin; the accessories, and other items included with the product; and the language used on the packaging, the parts, and any related instructions or printed material related to the products. This website is not sanctioned or approved by any manufacturer or tradename listed. Designated trademarks, brand names and brands appearing herein are the property of their respective owners.