GE / IP FANUC Series 90/30 In Stock
SKU 2176312 UPC 0458302419455
All product names, trademarks, brands and logos used on this site are the property of their respective owners. PDF Supply is not an authorized distributor, reseller or representative of the products featured on this website. The depiction, description or sale of products featuring these names, trademarks, brands and logos is for identification purposes only and is not intended to indicate any affiliation with or authorization by any rights holder.
The GE Fanuc IC693PRG300 is a G300 Hand-Held Programmer (HHP). This tool enables users to develop, debug, and monitor logic programs. Users can also monitor data tables and configure parameters for PLC units and I/O points. It uses the Statement List Language and it is possible to program this HHP with some models of the Series 90-30 PLC. The Hand-Held Programmer cannot view or edit the user logic program in any Series 90-30 CPU with a model number of 350 and above. For these CPUs, users can use Logicmaster 90-30, VersaPro or Control programming software.
There is a 15-pin D-type connector on the Series 90-30 PLC. This is located in the CPU baseplate of the power supply. This connector enables the HHP to connect to the CPU serial port. To physically connect them, use a 6-foot (2-meters) long cable (IC693CBL303). This will provide power to the HHP and also emits a signal that lets the PLC know a HHP is attached. It’s possible to connect or disconnect the HHP while the PLC is under power. In order to communicate with a PLC, the HHP does not need communications parameter configuration. This aids troubleshooting issues when there is a communication problem between the PC and a PLC.
Repair your IC693PRG300
PDF Supply can repair your IC693PRG300 in 3-5 business days. And PDF Supply stands by all of its repairs with a 1 year customer satisfaction warranty.
Hand Held Programmer for 90-30
Hand Held Programmer for 90-30
Hand Held Programmer (HHP) for the 90-30 can be ordered under part#
Memory Card IC693ACC303 (Program Upload)
There are program restrictions
User logic program in CPU 350 and above cannot be viewed or edited by the HHP
The CPU in Series 90-30 Hand-Held Programmer (HHP IC693PRG300) To Be Used To Edit Data Values in %R Registers
The Series 90-30 Hand-Held Programmer (HHP IC693PRG300) can be used to edit data values in %R registers in which CPUs.
All 90-30 CPUs except the 374 *
Configuring a Profibus Field Control Module
The Profibus IC670PBI001 BIU comes default from the factory set to the 'Autoconfiguration' mode.
Steps to setup module
Other option of configuring the module can be done with a 90-30 hand held programmer IC693PRG300 Hand Held Programmer (HHP) With Cable
Profibus Bus Interface Unit
Catalog Number; IC670PBI001-DG/EG
Firmware ID: CORE Version 2.60
COMM Version 3.50
GSD File: Version 3.30
Field Update Kit: 44A740056-G06
GSD file, GEF_0534.GSD (Revision 3.30)
For more information on the IC693PRG300 Hand Held Programmer of the GE 90-30 Series, please see the Datasheet Manual.
PDF Electric & Supply Inc. sells new, new surplus and refurbished products which are sourced through independent channels. All warranties and support, if applicable, are with PDF Electric & Supply Inc. and not the manufacturer. PDF Electric & Supply Inc. is not an authorized distributor or representative for the listed manufacturers and makes no representations as to any quality control performed by any listed manufacturer on the products. The products listed on this website may vary as to their country of origin; the accessories, and other items included with the product; and the language used on the packaging, the parts, and any related instructions or printed material related to the products. This website is not sanctioned or approved by any manufacturer or tradename listed. Designated trademarks, brand names and brands appearing herein are the property of their respective owners.