GE / IP FANUC Series 90/30 In Stock

World's Largest Warehouse

of GE 90-30, Genius, and RX7i

Mon-Fri 8AM-5PM EST



Rated 4.7/5 Based on 15 ratings.

Rate your purchase of the IC693PWR322

SKU 2175303  UPC 0563559722569

All product names, trademarks, brands and logos used on this site are the property of their respective owners. PDF Supply is not an authorized distributor, reseller or representative of the products featured on this website. The depiction, description or sale of products featuring these names, trademarks, brands and logos is for identification purposes only and is not intended to in indicate any affiliation with or authorization by any rights holder.

PDF Supply is NOT an authorized distributor for this manufacturer and therefore the manufacturer’s warranty does not apply. Product comes with PDF Supply's 1-year, 2-year, or 3-year warranty.

Technical Specifications for IC693PWR322

ManufacturerGE Fanuc
SeriesSeries 90-30
Part NumberIC693PWR322
Product TypeStandard Power Supply
Power Output30 Watts
Nominal Input Voltage24 Volts DC
Input Voltage Range18 to 56 Volts DC
Over-Current Limit4 Amps Peak for 100 Milliseconds
Over Voltage Limit6.4 to 7 Volts DC
Input Power50 Watts

Product Description

The GE Fanuc IC693PWR322 is a 24/48 VDC standard power supply. The standard unit, which does not include a battery, is designed to work off a nominal input of 12V DC or 48V DC and has a 30 watt output. This unit can be mounted in a standard power supply slot through any IC693 PLC baseplate. Although it is capable of maintaining all outputs (within specifications) with input voltages as low as 18VDC, it will not start with initial input voltages of less than 21 VDC. This power supply provides three separate outputs. These are +5VDC,  +24VDC relay output for powering circuits on any IC693 relay output module and +24VDC Isolated power for Input modules.

When using this power supply, users can calculate the power requirements specific to their application. To do this, you first need to determine the total output load by checking the specs listed in the IC693 PLC Installation and Hardware Manual. This will show the specifications for individual modules. The total output load should be multiplied by 1.5 to determine input power value. To calculate the input current requirement, divide the input power by the operating source voltage. As the operating source voltage may vary, you should use the lowest measured or estimated input voltage to determine the maximum input current. Operators who are making this calculation should also allow for start-up surge current requirements and allow a margin of 10-20% for variation.


Technical Specifications

Nominal Rated Voltage: 24 or 48 volts DC
Input Voltage Range: 21 to 56 volts DC
Input Power: 50 W at full power
Load Capacity: 30 Watts
Location on Baseplates:   Leftmost Slot
Communication: RS 485 Serial Port


The GE Fanuc IC693PWR322 Standard Power Supply is a 12/48 Volts DC rated standard power supply from the GE Series 90-30 standard power supply family. The GE Series 90-30 standard power supplies do not come with a built-in battery, and unlike the AC supplies, the IC693PWR322 Power Supply is built for a nominal input rating of 24 Volts DC or 48 Volts DC. The IC693PWR322 Power Supply is installed in a slot that is reserved for a standard power supply on any Series 90-30 PLC baseplate. The IC693PWR322 Standard Power Supply has an input voltage range of 18 to 56 Volts DC, and even though it is capable of maintaining every output level at the lowest possible input value of 18 Volts DC, it will not start with any initial input voltage less than 21 Volts DC. Like the GE high-capacity power supplies, the IC693PWR322 Power Supply comes with 3 separate output voltage ratings, which are the standard +5 Volts DC output voltage, the 24 Volts DC isolated output voltage, and the 24 Volts DC relay output voltage. The 24 Volts DC relay output provides power to all Series 90-30 relay output module circuits. 


The GE Fanuc Series 90-30 IC693PWR322 Standard Power Supply’s 24 Volts DC isolated output is used internally by some IC693 I/O modules, and it can also be used to provide external power to 24 Volts DC rated input modules. The IC693PWR322 Power Supply features built-in current limiting functions that automatically shut down the power supply in the event of a direct short fault to protect the internal components from damage. It also features an auto-ranging capability that completely eliminates the need for jumpers for assigning the incoming power levels. The IC693PWR322 Power Supply has an inrush current rating of 4 Amps and a minimum hold-up time of 14 milliseconds.

Technical Information



Nominal Rated Voltage Input Voltage Range

Start Run

24 or 48 VDC


21 to 56 VDC

18 to 56 VDC

Input Power

Inrush Current

50 watts maximum at full load

4A peak, 100 ms maximum

Output Power

5 VDC:  15 watts maximum

24 VDC Relay:  15 watts maximum

24 VDC Isolated:  20 watts maximum

NOTE: 30 watts maximum total (all three outputs)

Output Voltage

5 VDC:  5.0 VDC to 5.2 VDC (5.1 VDC nominal)

24 VDC Relay: 24 to 28 VDC

24 VDC Isolated:  21.5 VDC to 28 VDC

Protective Limits Overvoltage: Overcurrent;


5 VDC output:  6.4 to 7 V

5 VDC output:  4 A maximum

Holdup Time:

14 ms minimum


Refer to data sheet, GFK-0867B, or later version for product standards, and general specifications.



Troubleshooting IC693PWR322

Troubleshooting information is available on IC693PWR322’s website page; it also includes a datasheet user-manual and a wiring diagram.  


Repair your IC693PWR322

PDF Supply can repair your IC693PWR322 in 3-5 business days. And PDF Supply stands by all of its repairs with a 1 year customer satisfaction warranty.

Customer Questions and Answers

  • Question:  What is an IC693PWR322?  Answer:  The IC693PWR322 is a Standard Power Supply. This module is a 30 watt output supply designed for 24 VDC or 48 VDC nominal inputs. It will accept an input voltage range from 18 VDC to 56 VDC. Although it is capable of maintaining all outputs (within specifications) with input voltages as low as 18VDC, it will not start with initial input voltages of less than 21 VDC. The specifications for this product are on IC693PWR322's website page. 
  • Question:  How many outputs does this power supply provide?   Answer:  The IC693PWR322 provides 3 outputs. 
  • Question:  What are those outputs?   Answer: 
    • +5 VDC output 
    • +24 VDC "Relay" power output, which provides power to circuits on Series 90-30 Output Relay modules.
    • "Isolated" +24 VDC, which is used internally by some modules and can also be used to provide external power for 24 VDC Input modules.
  • Question:  What is the load capacity for IC693PWR322?   Answer:  30 watts
  • Question:  What is the input for IC693PWR322?   Answer:  24 or 48 VDC
  • Question:  Where should the power supplies be installed?   Answer:  Power supplies must be installed in the leftmost slot in all baseplates.
  • Question:  What does it mean when the OK light is green?   Answer:  It is referring to the CPU. If the OK light is green it means that the CPU has reported back that it is in a fully functional mode.
  • Question:  How can I tell if my IC693PWR322 is not working?   Answer:  If your PWR or OK light is not on, if the power supply is excessively loud, if the PS PORT is not blinking, or if your RUN light does not come on when you have the module running then your product may need repair.

For more information on the IC693PWR322 Standard Power Supply Module of the GE 90-30 Series, please see the Datasheet Manual. 


ST. LOUIS, Feb. 1, 2019 – Emerson today announced it has completed the purchase of Intelligent Platforms from General Electric.

Common related search terms: BatteryBuyDatasheetEmersonManualPriceRepairSpecificationTroubleshootWiring


PDF Supply sells used surplus products. PDF Supply is not an authorized distributor, affiliate, or representative for the brands we carry. Products sold by PDF Supply come with PDF Supply’s 1-year, 2-year, or 3-year warranty and do not come with the original manufacturer’s warranty. Designated trademarks, brand names and brands appearing herein are the property of their respective owners. This website is not sanctioned or approved by any manufacturer or tradename listed.

Rockwell Disclaimer: The product is used surplus. PDF Supply is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because PDF Supply is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, PDF Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. PDF Supply also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. PDF Supply also makes no representations as to your right to install any such firmware on the product. PDF Supply will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.