GE / IP FANUC Series 90/30 In Stock
Preowned
PDF Supply Company, LLC is not an authorized distributor for GE Fanuc Emerson
The IC695FTB001 provides an active fiber interface that extends the I/O capability of the IC695PMM335 PACMotion Multi-Acis Motion Controller. The FTB provides a broad range of configurable I/) for the axes on the PMM335, supporting extensive distributed, configurable digital and analog I/O for complex machines.
The FTB allows motion-centric I/O to be distributed up to 100 meters from the RX3i rack. Servo amplifiers and motion I/O can be distributed with up to 100 meters between nodes, allowing 400 meters maximum from the controller.
In addition to simple I/O, FTB I/O is configurable for motion-specific functionality such as Touch Probe inputs, Over Travel Limit switches, Home switches, and A Quad B Encoder and Marker inputs.
The Horner APG +/-10V Isolated Analog Input Modules provide four analog input channels with 14-bits of resolution. The isolation levels for this unit are channel-to-channel and channel-to-ground. This module converts voltage input signals to digital values (-32,000 to +32,000), which are placed directly into the %AI table of the PLC CPU. Each of the four channels of the module has a programmable setpoint (the level of which is set in the PLC program via four %AQ output registers). When the analog input value reaches or exceeds the setpoint, a corresponding digital input %I is energized. The first four %Is represent the four input channel setpoint alarms respectively.
Steady-State Power Consumption | ADC405: .4W / 80mA @ 5V, 2.16W / 90mA @ 24V ADC410: .7W / 140mA @ 5V, 1.2W / 50mA @ 24V |
Power Requirements | 19.2VDC - 28.8VDC; 0.45 Amps @ 24V |
24V Outputs | 8 optical isolated; source; open load & short detection |
24V General Purpose | 16 optically isolated; source/sink |
5V Inputs / Outputs | 4 |
5V | 8 (6 differential/single-ended; 2 differential) |
Analog Inputs | 2 +/- 10V differential |
Analog Outputs | 2 +/- 10V single-ended |
24V Power Output | |
5V Power Output | 0.5 amp max. |
Quad Encoder Open Circuit Detection | Yes |
I/O Function Assignment | Configurable |
Steady-State Power Consumption | ADC405: .4W / 80mA @ 5V, 2.16W / 90mA @ 24V ADC410: .7W / 140mA @ 5V, 1.2W / 50mA @ 24V |
Power Requirements | 19.2VDC - 28.8VDC; 0.45 Amps @ 24V |
24V Outputs | 8 optical isolated; source; open load & short detection |
24V General Purpose | 16 optically isolated; source/sink |
5V Inputs / Outputs | 4 |
5V | 8 (6 differential/single-ended; 2 differential) |
Analog Inputs | 2 +/- 10V differential |
Analog Outputs | 2 +/- 10V single-ended |
24V Power Output | |
5V Power Output | 0.5 amp max. |
Quad Encoder Open Circuit Detection | Yes |
I/O Function Assignment | Configurable |
Question: What is the IC695FTB001? Answer: The IC695FTB001 provides an active fiber interface that extends the I/O capability of the IC695PMM335 PACMotion Multi-Acis Motion Controller. The FTB provides a broad range of configurable I/) for the axes on the PMM335, supporting extensive distributed, configurable digital and analog I/O for complex machines.
The FTB allows motion-centric I/O to be distributed up to 100 meters from the RX3i rack. Servo amplifiers and motion I/O can be distributed with up to 100 meters between nodes, allowing 400 meters maximum from the controller.
Question: What power source does the IC695FTB001 require? Answer: The IC695FTB001 requires 19.2VDC - 28.8 VDC, or 0.45 Amps @ 24V.
Question: What is the CPU Version? Answer: The IC695FTB001 requires PACSystems Rx3i firmware relase 5.60.
Question: What happens if there is a system failure? Answer: In the event of a system malfunction, such as loss of communication with the PMM, the FTB sets its I/O to the user-configured state.
Common related search terms: Emerson
PDF Supply Company, LLC. sells surplus and refurbished products, which are sourced through independent channels. All warranties and support, if applicable, are with PDF Supply Company, LLC. and not the manufacturer; manufacturer warranties do not apply. PDF Supply Company, LLC. is not an authorized distributor or representative for the listed manufacturers and makes no representations as to any quality control performed by any listed manufacturers on the products. The products listed on this website may vary as to their country of origin; the accessories, and other items included with the product; and the language used on the packaging, the parts, and any related instructions or printed material related to the products. PDF Supply Company, LLC. does not sell or license software that may be needed to operate certain hardware and customers must obtain any necessary software licensing, maintenance, or upgrades from the manufacturer or other authorized source. This website is not sanctioned or approved by any manufacturer or other authorized source. This website is not sanctioned or approved by any manufacturer or tradename listed. Designated trademarks, brand names and brands appearing herein are the property of their respective owners.