GE / IP FANUC Series 90/30 In Stock
Other Available Revisions for the 44A749939-001 44A749939-001-44A749939001A44A749939-001-44A749939001B44A749939-001-44A749939001C44A749939-001-44A749939001CA44A749939-001-44A749939001D44A749939-001-44A749939001E44A749939-001-44A749939001F44A749939-001-44A749939001G44A749939-001-44A749939001H44A749939-001-44A749939001I44A749939-001-44A749939001J44A749939-001-44A749939001K44A749939-001-44A749939001L44A749939-001-44A749939001LT44A749939-001-44A749939001M44A749939-001-44A749939001N44A749939-001-44A749939001O44A749939-001-44A749939001P44A749939-001-44A749939001Q44A749939-001-44A749939001R44A749939-001-44A749939001RR44A749939-001-44A749939001S44A749939-001-44A749939001T44A749939-001-44A749939001U44A749939-001-44A749939001V44A749939-001-44A749939001W44A749939-001-44A749939001X44A749939-001-44A749939001Y44A749939-001-44A749939001Z
|Product Type||Interface Module|
|Power Source Voltage||5 Volts|
|Expanded Channel Scanning||Supported|
|Connectors||2 DB Connectors|
|Number of I/O Channels||8|
J1320-P001 S6PI0 MODULE 90-70 Series Six Rx7i Parallel GE Fanuc PLC 44A 44A7499390 44A749939001
The 44A749939-001 module is manufactured by GE Fanuc and it is part of the GE Series 90-70 product line. The 44A749939-001 module is an industrial I/O interface module that comes with 8 I/O channels as well as with 2 DB37 connectors. Its channels and connectors allow it to connect and communicate with devices from the GE Fanuc PACsystem and Rx7i series. The 44A749939-001 I/O interface module meets the CE and cULus industrial standards. The 2 DB37 connectors on the front of the 44A749939-001 module are made to host the upstream and downstream connections for the module while using just 1 bus device. This I/O interface module has an open enclosure design that does not offer it much protection from liquids and debris. It should either be used only in clean environments or installed in a stronger enclosure.
The GE Fanuc 44A749939-001 I/O interface module from Series 90-70 can support both normal and expanded channel scanning. It uses a 5 Volts-rated bus as its power source. The users can configure the 44A749939-001 interface module for their applications through a programmer device or with a personal computer. When this module is working with a Series Six GE system, it can monitor all of the I/O in the system. It can also support operation in a passive mode as well in the active mode. The 44A749939-001 I/O interface module is made to be air-cooled, and when it is installed, it needs to have specified clearances around it that are clear and wide enough for air to circulate properly and cool the module down during operation.
The GE Fanuc 44A749939-001 I/O module is a Series 90-70 I/O module. It is compatible with the GE Rx7i series and PACsystem PLC devices. The module has been listed with cULus and it is CE certified. This Series 90-70 module has been designed to handle complex applications like batch processing, modular redundancy, and several others. The front section of the module is equipped with 2 connectors for upstream and downstream connections using a single bus. The module supports up to 8 channels. LED indicators are present on the front side of the module to indicate different events. The 44A749939-001 I/O module has an open enclosure and it should be used and stored in a clean place that is free from EMC contaminants. The I/O module can be easily connected to a programmer or a personal computer for configuration.
The 44A749939-001 I/O module can be used to control different PLC devices and different I/O devices in the field. It can be connected with other I/O buses from the Rx7i series. The module is powered through the 5 Volts bus. The module can be easily installed in the terminal block of the PAC and Rx7i systems. During installation, the power should be fully disconnected to avoid electrical damage. The 44A749939-001 I/O module has a dielectric isolation rating of 1500 Volts. For connections, the front side of the module comes with RJ11 and RS-232 serial ports. These ports offer high speed data transfers. The I/O module supports passive mode operation and it can also be used for normal and expanded channel scanning. Proper airflow should be maintained during operation to maintain the specified operating temperature of the module.
PDF Electric & Supply Inc. sells new, new surplus and refurbished products which are sourced through independent channels. All warranties and support, if applicable, are with PDF Electric & Supply Inc. and not the manufacturer. PDF Electric & Supply Inc. is not an authorized distributor or representative for the listed manufacturers and makes no representations as to any quality control performed by any listed manufacturer on the products. The products listed on this website may vary as to their country of origin; the accessories, and other items included with the product; and the language used on the packaging, the parts, and any related instructions or printed material related to the products. This website is not sanctioned or approved by any manufacturer or tradename listed. Designated trademarks, brand names and brands appearing herein are the property of their respective owners.