1-919-535-3180 | 1-800-360-6802

GE / IP FANUC Series 90/30 In Stock

World's Largest Warehouse

of GE 90-30, Genius, and RX7i



Mon-Fri 8AM-5PM EST



Rated 4.8/5 Based on 14 ratings.

Rate your purchase of the IC697CHS790


SKU 2170064  UPC 0799705795020

All product names, trademarks, brands and logos used on this site are the property of their respective owners. PDF Supply is not an authorized distributor, reseller or representative of the products featured on this website. The depiction, description or sale of products featuring these names, trademarks, brands and logos is for identification purposes only and is not intended to indicate any affiliation with or authorization by any rights holder.

MSRP $1151


  ON SALE ! 

18 in stock

✓  2 Year PDF Supply warranty

*Need a Specific Revision?

"Like New Condition"



Save $956

10 in stock

✓  2 Year PDF Supply warranty

*What is Remanufactured?

Product Description

The IC697CHS790 is a 9-slot Rear Mount for IC697 programmable controller used for CPU and I/O configurations.
There is capability for one power supply for the standard 9-slot rack located at the leftmost module position. The IC697CHS790 rack mounts in a 10 inch deep enclosure where fans are not normally required. The rack’s dimensions are 11.15” H x 19” W x 7.5” D with controller slot width being 1.6” W and the width of the supply slot at 2.4” W. Each rack offers a slot sensing for rack-type I/O created for the IC697 PLC. No switches or jumpers on the I/O modules are needed.  

The mounting for the IC697CHS790 rack requires enough space to allow for proper cooling of system modules. The requirements for mounting must be determined according to the application and the proper rack ordered. The mounting flanges are conveniently factory installed in the rack’s side panels.

The IC697 I/O modules interlock by use of a key to avoid unintended interchange of a module type for another module type. Each module includes a key that latches on mechanically to the center rail of the rack, where it stays until the module is removed. If the module is not the correct type, it cannot be inserted into that rack slot. A rack number from 0-7 must be assigned when there are several racks in a system; the CPU rack is always rack 0. The number of each rack will be determined by the PLC from the four jumpers on the rack’s backplane. The backplane location is directly behind the power supply, and the jumpers are on the backplane.  

Technical Specifications

Module Type: Standard Rack
Mounting Location: Rear(panel)
Number of Slots: 9 (plus power supply)
Type: Double width
Dimensions: 11.15 x 19.00 x 7.5 in. (H x W x D)
Internal Power Used:  20 amps @ 5 VDC


17 slot Rack, 9 Slots, Rear Mount IC697C IC697CH IC697CHS
ST. LOUIS, Feb. 1, 2019 – Emerson today announced it has completed the purchase of Intelligent Platforms from General Electric.

Common related search terms: ConfigurationDatasheetDimensionEmersonManualPDFPLCPriceRepairSpecificationTroubleshootUser-ManualWiring

All online orders placed before 4:30 PM EST “SHIPS SAME DAY FREE!" World’s largest warehouse of Factory Sealed GE 90-30 PLC, GENIUS I/O and RX7i PACSystem.highlight_off

PDF Electric & Supply Inc. sells new, new surplus and refurbished products which are sourced through independent channels. All warranties and support, if applicable, are with PDF Electric & Supply Inc. and not the manufacturer. PDF Electric & Supply Inc. is not an authorized distributor or representative for the listed manufacturers and makes no representations as to any quality control performed by any listed manufacturer on the products. The products listed on this website may vary as to their country of origin; the accessories, and other items included with the product; and the language used on the packaging, the parts, and any related instructions or printed material related to the products. This website is not sanctioned or approved by any manufacturer or tradename listed. Designated trademarks, brand names and brands appearing herein are the property of their respective owners.