PDF Electric and Supply



Buy NowIC697CMM711
IC697CMM711 Wiring

Rated 4.8/5 based on 13 ratings.
  • IC697CMM711
  • IC697CMM711 Wiring

Product Description

The IC697CMM711 is a Single-Slot Communications Coprocessor Module (CMM) from the GE 90-30 series.
The module comes standard with soft switch configuration (eliminating the need for switches and/or jumpers), three status LEDs, pushbutton reset control, and two serial ports. The module uses a 12 Mhz, 80C186 microprocessor. Additionally, no battery is needed.

The CMM is part of a family of communication modules and demonstrates both communications control (CCM), remote terminal (RTU), and general IC69 communications (SNP) functionality. CCM, RTU and SNP are available on either or both serial ports in any of nine possible configurations: CCM/CCM, CCM/RTU, RTU/CCM, RTU/RTU, SNP/SNP, SNP/CCM, CCM/SNP, SNP/RTU, and RTU/SNP. The module delivers both the RS-232 and RS-485 interfaces and communicates with the PLC CPU via the backplane. Numerous CMMs can be placed in just one IC697 PLC system.

Functions allowed by the IC697CMM711 CMM in the CCM operation mode include read/write of register, input and output tables, bit set/clear of inputs and outputs, read of scratch pad, Q sequence commands for fast reads, and diagnostic status word modification. In master/peer CCM configurations, the CMM initiates communications with remote devices through application ladder program communications requests.

The IC697CMM711 module’s status is viewable via three LEDs. Activity of the serial ports are identified in port 1 LED and port 2 LED. The top LED will blink when the module is powered up, and once diagnostics are completed effectively, the top LED will remain lit. The top LED will always identify module state.   

Technical Specifications

Module Type:  Communications Coprocessor
Number of Slots: One (Single Slot)
Protocols: CCM, RTU, SNP and SNPx
Connects to: MS-DOS or Windows programming
Serial Ports: 2
Current Required:    0.7 amps



GE Fanuc GE Fanuc Series 90-70

SKU 2174044  UPC 0799705795013

Part Number: IC697CMM711 / ic697cmm711
Mfr/Brand Name: GE Automation
Mfr Number: IC697CMM711 / ic697cmm711
Type: Communications Co-processor Module.

Technical Specifications

  • Communications Coprocessor
  • CCM, RTU, SNP, and SNPx Protocols
  • Single-Slot Module
  • SNP/SNP-X Protocol (master, slave)
  • CCM Protocol (master, slave, peer
  • RTU Modbus Protocol (slave only)
Troubleshooting and Product Information for IC697CMM711

Download product information, troubleshooting guides and operation manuals to get your PLC operational.

New IC697CMM711
Price: $2,950
3 In Stock
1 Year PDF Supply Warranty

*Need a Specific Revision?

Surplus New IC697CMM711
Price: $2,450
1 In Stock
3 Year PDF Supply Warranty

*What is Surplus New?

Reman IC697CMM711
Price: $695
In Stock

2 Year PDF Supply Warranty

*What is Remanufactured?

Repair Your IC697CMM711
Price: $395
1 Year PDF Supply Warranty
Call For Assistance

Other IC697CMM711

Available Revisions:

Confirm Your Revision Number

1C697CMM711 , GEFIC697CMM711 , CIMIC697CMM711

Serial Ports                                                        RS-232 and RS-422 / RS-485 compatible

Current Required                                               0.7 amps

VME                                                                   System designed to supplrt VME Standard C.1

Troubleshooting IC697CMM711

Troubleshooting information is available on IC697CMM711's website page; it also includes a datasheet user-manual and a wiring diagram.

Repair your IC697CMM711

PDF Supply can repair your IC697CMM711 in 3-5 business days. And PDF Supply stands by all of its repairs with a 1 year customer satisfaction warranty.

Customer Questions and Answers

  • Question:  What is an IC697CMM711?  Answer:  The IC697CMM711 is a Communications Coprocessor module from the GE Fanuc 90-70 Series.
  • Question:  How many LED lights are on IC697CMM711?  Answer:  There are 3. There is an OK light, an LED for Port 1, and an LED for Port 2.
  • Question:  If I power up my IC697CMM711 and the OK LED light is not on or is blinking- What does that mean?  Answer:  It means you have a problem with your processor and won't be able to test it. 
  • Question:  What is the first thing I should do when testing IC697CMM711?  Answer:  In Proficy, you should set up the configuration so it matches what you see on the modules. 
  • Question:  What should I do next?  Answer:  You want to clear Controller and I/O Fault Table. Then download and run (only configuration and logic) that configuration. You're going to use a program called Test Comm next.
  • Question:  How do I use that?  Answer:  You will hit the online/offline icon (the lightning bolt) so you can detach the computer from the processor. Then, you're going to close out of Proficy and open Test Comm. Go to CMM type protocol (which allows a signal exchange between the software, the computer, and the IC697CMM711). You will use a shielded cable to get that signal over to your IC697CMM711. (One end goes into the computer and one ends goes into Port 1 on your IC697CMM711.) You will click a button that says "Try All" and you will be looking for a response. You will do the same with Port 2. 
  • What should I do if my IC697CMM711 isn't responding properly?  Answer:  Your IC697CMM711 may need repair

For more information on the IC697CMM711 Communications Coprocessor Module of the GE Fanuc 90-70 Series, please see the Datasheet User-Manual. 


Need To Order A Specific Revision?

Give us a call at 1-800-360-6802 or 1-919-535-3180.

We can help you with your Revision specific needs.

Free Overnight delivery on orders over $500!

What is New Surplus?

These “New Surplus” units are a great cost saving alternative. This product is sealed in the original manufacturer’s packaging with all sub-assemblies and documentation. May indicate older date code. Comes with a PDF Supply 3-year warranty.

Free Overnight delivery on orders over $500!

What is Surplus New?

Surplus New - New unused and includes all sub-assemblies and documentation. Product may ship in manufacturer or PDF Supply packaging. May indicate older date code. Includes a PDF Supply 3 Year Warranty.

Free Overnight delivery on orders over $500!

What is Reconditioned?

Reconditioned products from PDF Supply are a cost-effective alternative to new and obsoleted PLC products. Every part is reconditioned down to the circuit board level and updated to the latest revision. All parts are thoroughly inspected and hand-cleaned before being functionally tested in a fully configured system.

Our Reconditioned Products always come with a PDF Supply 2-Year Warranty.

Free Overnight delivery on orders over $500!

What is a Verified Substitute?

A verified substitute new product is a "drop in" replacement designed with identical specifications as the OEM product. It will meet all electrical and dimensional charactertics at a substanstially reduced price.

Free Overnight delivery on orders over $500!

Download Lastest Documentation

Please visit this manufacturer's website to download the lastest manuals and datasheets.

Lowest Price Guarantee

We stand behind our prices with a lowest price guarantee. If you find a legacy GE PLC part advertised for less on an authorized GE PLC distributor website, simply contact us and send us a link to the lower advertised price. We will match that price and ship overnight FREE. The item must be in stock, in similar condition and be able to ship same day.

Free Shipping

FREE Overnight Delivery for Continental US orders over $500!

FREE Ground Delivery for Continental US orders under $500!

US orders placed Monday - Friday before 5pm EST will ship same day.

Canada/Mexico orders placed Monday - Friday before 3:30pm EST will ship same day.

International orders will ship the following business day.