PDF Electric and Supply

1-800-360-6802
1-919-535-3180
sales@pdfsupply.com

IC697MDL753

Buy NowIC697MDL753
IC697MDL753
IC697MDL753 Wiring

Rated 4.7/5 based on 10 ratings.
  • IC697MDL753
  • IC697MDL753 Wiring

Product Description


The IC697MDL753 is a 5/48 Volt DC, 0.5 Amp, Negative Logic, 32-Point Output module from the GE Fanuc 90-70 Series. This module provides 32 points divided into 2 isolated groups of 16 points each.  The rated voltage on this module can be 5 volts DC or 10 to 60 volts DC.  It provides a high degree of inrush current at 10 to 60 volts which makes the outputs suitable for a wide range of loads which have such characteristics.  It also operates at TTL levels.   

The outputs are ideal for a wide spectrum of loads. This is due to the effective delivery of high inrush current which is between 10 to 60 volts. You can spot LED indicators at the top of each logic point of the PLC module. Their primary function is to display the ON-Off status of each logic point of the PLC. Jumpers and DIP switches are not required for the configuration of I/O references located on the module. The configuration of the module is achieved using Microsoft’s MS-DOS or Windows NT & 95 operating systems over the TCP/IP protocol. Programming devices can be either compatible personal computers, PS/2, AT or IBM.

As mentioned earlier, the IC697MDL753 PLC output module is compatible with a wide variety of loads which include indicators, motor starters, solenoids and TTL interfaces. Due to the significant overall heat dissipation with each group of modules, the maximum current is set to 4 Amps. Each output can deliver a current rating exceeding its long-term rating. The ability of each output point to deliver a current largely depends on the device’s current rating as well as the duration the device is powered ON. Since the Logic output module has no replaceable fuses, a ¾ Amp 250-volt fuse is connected externally to each output point. The fuse models are either Little Fuse 312.750 or Bussmann AGC-3/4.

There are certain field wiring procedures that need to be followed when setting up the modules.  First, ensure that you’ve turned off the power during removal or installation of terminal boards. The jackscrew that secures the terminal board in place can be located when opening the hinged door on the module. The screw is then turned in a counter clockwise direction to loosen the detachable terminal board. The board is thereafter removed by grabbing it and swinging it outward. Be cautious when removing the terminal board. The hinged door may become damaged if it is used to remove the terminal board.  The board can accommodate wires ranging from AWG#22 (0.36mm2) right through AWG #14 (2.10mm2). Kindly note that a .135-inch maximum diameter is not to be exceeded when using the AWG#14 (2.10mm2) wire.

For a proper connection, you can terminate two wires on any terminal if the wires are of the same size. The terminal board accepts a maximum of 40 AWG#14 wires. If the said wires are to be used, then the wire markers should be placed accordingly. The terminal board is designed to accept a maximum of (40) AWG #14 (2.10 mm2) wires. To provide ample space for the hinged door to close, wire markers should be placed at least 8 inches (203 mm) from termination end when using the AWG #14 wires.  After connections are completed for all modules in the rack, wire bundles must be secured. It’s recommended that cable ties are firmly wrapped round the wire bundles. Additional cable ties are used when larger wire bundles are involved. Each module comes with a door label insert which displays its wiring information. After completion of the field wiring, the terminal board should be firmly secured on the rack. For ideal ventilation of the module, a 6-inch clearance is recommended above and below the rack grill.

Technical Specifications


Rated Voltage: 5 volts DC or 10 to 60 volts DC
Number of Outputs: 32 Outputs (2 groups of 16)
Output Current: 16 mA/ point @ 5 VDC, 0.5 Amps/ point, 4 Amps/ group @ 10 to 60 VDC
Current Required: 0.25 Amps
Output Voltage Range:   5 volts DC or 10 to 60 volts DC
DC Power: Yes

 

GE Fanuc GE Fanuc Series 90-70

SKU 2175357  UPC 0241864939345

Part Number: IC697MDL753 / ic697mdl753
Mfr/Brand Name: GE Automation
Mfr Number: IC697MDL753 / ic697mdl753
Type: 5/48 volts DC, 0.5 Amp, Neg Logic Output Module, 32 Output Points

Troubleshooting and Product Information for IC697MDL753

Download product information, troubleshooting guides and operation manuals to get your PLC operational.

Reman IC697MDL753
Price: $406
7
In Stock

2 Year PDF Supply Warranty

*What is Remanufactured?

Save
 57%
Repair Your IC697MDL753
Price: $295
1 Year PDF Supply Warranty
Call For Assistance
1-800-360-6802

Other IC697MDL753

Available Revisions:

Confirm Your Revision Number

1C697MDL753 , GEFIC697MDL753 , CIMIC697MDL753

Specifications

Rated Voltage:

 

OutputsperModule:

5 volts DC (" 5%)

10 to 60 volts DC

32 (two groups of 16 outputs each)

Isolation:

1500 volts - any output to backplane 500 volts between input groups

Output VoltageRange: OutputCurrent

5 volts DC

10 to 60 volts DC

5 volts or 10 to 60 volts

 

16 mA maximum per point

0.5 amps maximum per point 4 amps maximum per group

OutputCharacteristics Inrush Current

10 to 60 volts DC: Output VoltageDrop:

5 volts DC:

10 to 60 volts DC: ResponseTime-On: ResponseTime-Off: OutputLeakage:

5 volts DC:

10 to 60 volts DC:

 

 

5 amps maximum for 20 ms

0.5 voltsmaximum (16 mA)

1 volt (2 ohms) maximum

1 ms typical

1 ms typical

250 Amaximum

1mAmaximum

Current Required from 5 V Bus:

.25 amp

VME

System designed to support the VME standard C.1

 

Troubleshooting IC697MDL753

Troubleshooting information is available on IC697MDL753's website page; it also includes a datasheet user-manual and a wiring diagram.


Repair your IC697MDL753

PDF Supply can repair your IC697MDL753 in 3-5 business days. And PDF Supply stands by all of its repairs with a 1 year customer satisfaction warranty.

Customer Questions and Answers


  • Question:  What is an IC697MDL753?  Answer:  The IC697MDL753 is a 5/48 Volt DC, 0.5 Amp, Negative Logic, 32-Point Output module from the GE Fanuc 90-70 Series. This module provides 32 points divided into 2 isolated groups of 16 points each. 
  • Question:  What are some of the features that IC697MDL753 provides?  Answer:
    • 32 points- 2 isolated groups of 16 points each
    • 0.5 amp capacity per point
    • high inrush capacity (10x rated current)
  • Question:  The LED indicators (located at the top of the module) do what?  Answer:  They let you know the on/off status of each point on the logic (PLC) side of the circuit. 
  • Question:  Can IC697MDL753 operate at TTL levels?  Answer:  Yes, it can.
  • Question:  What is special about the I/O references?  Answer:  They are configurable without the use of jumpers or DIP switches on the module. 
  • Question:  Configuration of IC697MDL753 is done through what?   Answer:  Configuration of IC697MDL753 is completed using the configuration function of MS-DOS, through Windows programming software on Windows 95, through Windows NT over Ethernet TCP/IP, or through the SNP port. 
  • Question:  What should I do in the event my IC697MDL753 is not working properly?   Answer:  Your IC697MDL753 may be in need of repair

For more information on the IC697MDL753 5/48 Volt DC, 0.5 Amp, Negative Logic, 32-Point Output Module of the GE Fanuc 90-70 Series, please see the Datasheet User-Manual. 

 

Need To Order A Specific Revision?

Give us a call at 1-800-360-6802 or 1-919-535-3180.

We can help you with your Revision specific needs.


Free Overnight delivery on orders over $500!

What is New Surplus?

These “New Surplus” units are a great cost saving alternative. This product is sealed in the original manufacturer’s packaging with all sub-assemblies and documentation. May indicate older date code. Comes with a PDF Supply 3-year warranty.


Free Overnight delivery on orders over $500!


What is Surplus New?

Surplus New - New unused and includes all sub-assemblies and documentation. Product may ship in manufacturer or PDF Supply packaging. May indicate older date code. Includes a PDF Supply 3 Year Warranty.


Free Overnight delivery on orders over $500!


What is Reconditioned?

Reconditioned products from PDF Supply are a cost-effective alternative to new and obsoleted PLC products. Every part is reconditioned down to the circuit board level and updated to the latest revision. All parts are thoroughly inspected and hand-cleaned before being functionally tested in a fully configured system.


Our Reconditioned Products always come with a PDF Supply 2-Year Warranty.

Free Overnight delivery on orders over $500!


What is a Verified Substitute?

A verified substitute new product is a "drop in" replacement designed with identical specifications as the OEM product. It will meet all electrical and dimensional charactertics at a substanstially reduced price.


Free Overnight delivery on orders over $500!


Download Lastest Documentation


Please visit this manufacturer's website to download the lastest manuals and datasheets.


Lowest Price Guarantee


We stand behind our prices with a lowest price guarantee. If you find a legacy GE PLC part advertised for less on an authorized GE PLC distributor website, simply contact us and send us a link to the lower advertised price. We will match that price and ship overnight FREE. The item must be in stock, in similar condition and be able to ship same day.

Free Shipping



FREE Overnight Delivery for Continental US orders over $500!

FREE Ground Delivery for Continental US orders under $500!

US orders placed Monday - Friday before 5pm EST will ship same day.

Canada/Mexico orders placed Monday - Friday before 3:30pm EST will ship same day.

International orders will ship the following business day.