1-919-535-3180 | 1-800-360-6802
sales@pdfsupply.com
GE / IP FANUC Series 90/30 In Stock
1-919-535-3180
1-800-360-6802
Mon-Fri 8AM-5PM EST
sales@pdfsupply.com
IC697PCM711
SKU 2174238 UPC 0587449550186
MSRP $6098
Common misspellings:
- 1C697PCM711
- lC697PCM711
- IC697PCM7l1
- IC697PCM71l
- IC697PCM711
Product Description
The IC697PCM711 is a Single-Slot Programmable Coprocessor (PCU) designed by GE for the Fanuc 90-70 series. The IC697PCM711 is equipped with a dual tasking module that can be programmed to perform various functions such as real-time computations, operator interface, and data functions that include storage, acquisition and communication. Communication from the module and the PLC CPU are by way of the backplane, and no application program support is needed. Several PCMs can be supported in a single IC697 PLC system, which can accommodate an optional expansion memory capacity of 512 Kbytes. Operation of the IC697PCM711 module can be done with or without an expansion memory daughter board. Base memory contains a maximum capacity of 95 Kbytes of user memory. The expansion memory daughter board allows expansion of program/data memory by 64,128, 256, or 512 Kbytes.
The power requirement for the IC697PCM711 module is 1.0amp, which is derived from the 5V bus. The lithium battery is conveniently located on the baseboard housing and supports memory; it has a shelf life of 10 years at 20 degrees Celsius or 64-degree Fahrenheit. Memory can be retained for six months without applied power. It is important to install a new battery before removing the old battery.
The IC697PCM711 module can be configured and programmed with various computer types such as the IC647 or IC640 or IBM-compatible PC, XT, or AT with PCM Development Software. The software is used to construct parameters for the serial port. The two serial ports are compatible and act at the same time. Jumpers and dip switches are not needed, but the board must be configured using the PCM software before operation can begin.
Technical Specifications
| Module Type: | Programmable Coprocessor |
| Number of Slots: | 1 (Single slot) |
| Current Required: | 1.0 Amp |
| Programmed by: | IC647, IC640 or IBM-compatible PC |
| Serial Ports: | 2 (RS232/RS-422/RS-485 compatible) |
| Battery Shelf Life: | 10 years at 20 deg.C (68 deg F) |
Technical Information
Specifications
|
Battery Shelf life Memory retention |
10 years at 20ï‚°C (68ï‚°F) 6 months nominal without applied power. |
|
Current required from 5V bus |
1.0 amp |
|
Serial Ports |
RS-232/RS-422/RS-485 compatible |
|
VME |
System designed to support the VME standard C.1 |
Troubleshooting
Troubleshooting IC697PCM711
Troubleshooting information is available on IC697PCM711's website page; it also includes a datasheet user-manual and a wiring diagram.
Repair your IC697PCM711
PDF Supply can repair your IC697PCM711 in 3-5 business days. And PDF Supply stands by all of its repairs with a 1 year customer satisfaction warranty.
Customer Questions and Answers
- Question: What is an IC697PCM711? Answer: The IC697PCM711 is a Programmable Coprocessor module from the GE Fanuc 90-70 Series.
- Question: What can IC697PCM711 be programmed to do? Answer: IC697PCM711 can be programmed to perform operator interface, real time computations, data storage, data acquisition, and data communications functions.
- Question: How does this module communicate with the PLC CPU? Answer: It communicates over the backplane.
- Question: What are some of the features of IC697PCM711? Answer:
- Single slot Coprocessor
- Dual Tasking
- MegaBasic
- CCM2 protocol
- 12 MHz, 80C186 microprocessor
- 90% of an IBM AT performance
- Up to 96 Kbytes battery-backed CMOS logic and data memory on board
- Supports up to 512 Kbytes optional expansion memory
- Programmed by IC647, IC640, or IBM-compatible Personal Computer
- 2 RS-422/RS-485 or RS-232 serial ports
- High performance access to PLC memory
- Real time calendar clock synchronized to PLC
- Reset pushbutton
- 3 status LEDs
- Soft Configuration (No dip switches or jumpers) with MS-DOS or Windows based programming software configuration function
- Simultaneous communications on both ports at up to 9.6 Kbaud or up to 19.2 Kbaud individually
- Question: What is one thing I should check when testing IC697PCM711? Answer: You should make sure that both of the ports are working.
- Question: What will you need to test this module? Answer: You will need your IC697PCM711, a slot rack, a power supply, and a processor.
- Question: How might I know if something is wrong with my IC697PCM711? Answer: If you hit try all and do not get an immediate reply, then there might be something wrong with your IC697PCM711.
- Question: What should I do if my IC697PCM711 is not functioning properly? Answer: Your IC697PCM711 may be in need of repair.
For more information on the IC697PCM711 Programmable Coprocessor Module of the GE Fanuc 90-70 Series, please see the Datasheet User-Manual.
PDFsupply Tech
The IC697PCM711 is a programmable coprocessor module that features dual tasking and three status LEDs. This module supports up to 96Kbytes of battery backed memory on board and up to 512 Kbytes in optional expansion memory.
Common related search terms: Battery, Datasheet, Emerson, Manual, PDF, PLC, Price, Repair, Specification, Troubleshoot, User-Manual, Wiring,
PDF Electric & Supply Inc. sells new, new surplus and refurbished products which are sourced through independent channels. All warranties and support, if applicable, are with PDF Electric & Supply Inc. and not the manufacturer. PDF Electric & Supply Inc. is not an authorized distributor or representative for the listed manufacturers and makes no representations as to any quality control performed by any listed manufacturer on the products. The products listed on this website may vary as to their country of origin; the accessories, and other items included with the product; and the language used on the packaging, the parts, and any related instructions or printed material related to the products. This website is not sanctioned or approved by any manufacturer or tradename listed. Designated trademarks, brand names and brands appearing herein are the property of their respective owners.