GE / IP FANUC Series 90/30 In Stock
Manufacturer | GE Fanuc |
---|---|
Series | Series 90-70 |
Part Number | IC697PWR711 |
Product Type | Power Module |
Voltage Type | AC and DC |
Nominal Voltage | 120/240 Volts AC, 125 Volts DC |
AC Operating Voltage | 90 to 264 Volts AC |
DC Operating Voltage | 100 to 150 Volts DC |
Operating Temperature | 32 to 140 degrees Fahrenheit |
Output Power | 100 Watts |
The IC697PWR711 is a GE Fanuc manufactured 100 Watt Power Supply Module for the Series 90-70. Features include operation from 120 VAC, 240 VAC, or 125 VDC, and there are three output voltages (100 watts total) as follows: +5 VDC output up to 20 amps; +12 VDC output up to 2 amps; -12 VDC output up to 1 amp. Other highlights include slide-in rack mount construction, electronic short circuit overcurrent protection, two rack operation from a single power supply, power factor correction for AC operation, and a jumper for overvoltage protection devices.
This module is rack-mounted and plugs directly into a 48-pin backplane-mounted connector in the leftmost slot of any standard IC697 rack or VME Integrator’s rack. It provides +5 volt, +12 volt and -12 volt power, and logic level sequencing signals to the backplane. The IC697PWR711 can be used in a single rack application or may to provide power to a second rack if the total load is within the supply rating. A prewired cable allows interconnection to the second rack. The power supply output will ride through at least one input line cycle with a total loss of input power at full load. Protection is delivered for overcurrent and overvoltage fault conditions.
This power supply module can operate from 120 VAC or 240 VAC nominal inputs. A nominal 125 VDC source is also an option. The specified range of operation is from 90 VAC to 264 VAC and from 100 VDC to 150 VDC. For uninterrupted operation (more than one hour) at low line voltages and high temps, some power derating must be applied.
Nominal Rated Voltage: | 120/240 VAC or 125 VDC |
Input Voltage Range: | 90 to 264 VAC or 100 to 150 VDC |
Input Power: | 135 watts at full load |
Output Power: | 100 watts |
Location on Baseplates: | Leftmost Slot |
DC Output: | + 5VDC, +12 VDC and -12 VDC |
The IC697PWR711 power module from GE Fanuc has been designed and manufactured as part of the GE Series 90-70 line of industrial power modules. The IC697PWR711 power module can provide other modules and systems with either AC or DC power, and its nominal voltage ratings are 120/240 Volts AC and 125 Volts DC. It can also deliver 100 Watts of maximum output power. The IC697PWR711 power module’s input power ratings are 135 Watts for typical operation and 160 Watts at the maximum. This power module is typically used in single-rack applications, but it can also provide power to a second rack as long as its power rating is enough to provide both racks with a reliable supply of power. It is easy to connect the IC697PWR711 power module to the second rack with a prewired cable.
The GE Fanuc Series 90-70 IC697PWR711 power module is made to operate in an ambient temperature range from 32 to 140 degrees Fahrenheit or 0 to 60 degrees Celsius. It can operate at higher temperatures too, but only after it has been derated to prevent damage. When this power module is being used to supply AC voltage to devices, it has an electronic short circuit protection feature as well as a power factor correction feature for safe operation. The AC operating voltage range for the IC697PWR711 power module is 90 to 264 Volts AC. Its DC voltage range for operation is 100 to 150 Volts DC. The IC697PWR711 power module uses a jumper for overvoltage protection.
Nominal Rated Voltage: |
120/240 VAC, or 125 VDC |
Input Voltage Range: |
|
AC Input |
90 to 264 VAC, 47 to 63 Hz |
DC Input |
100 to 150 VDC |
Input Power:Input Half Cycle Peak Inrush Power Factor |
135 watts (typical), 160 watts (maximum)3 amps (typical)> .93 |
Output Power: 2 |
100 watts maximum (total for all 3 outputs) |
Output Voltage: |
+5 VDC: 4.90 to 5.25 volts (5.07 volts nominal) |
|
+12 VDC: 11.64 to 12.6 volts 3 |
|
-12 VDC: -12.6 to -11.64 volts 3 |
Protective Limits - Overvoltage Limit: Overcurrent Limit: |
+5 VDC Output: 5.7 to 6.7 volts+5 VDC output: 21A (typical)+12 VDC output: 3.5A (typical)-12 VDC output: 1.6A (typical) |
Holdup Time: |
21 milliseconds minimum (from loss of AC input) |
Environmental -Operating Temperature: |
0°C to 60°C (32° to 140°F) operating2–40°C to +85°C (-40° to +185°F) storage |
Troubleshooting IC697PWR711
Troubleshooting information is available on IC697PWR711's website page; it also includes a datasheet user-manual and a wiring diagram.
Repair your IC697PWR711
PDF Supply can repair your IC697PWR711 in 3-5 business days. And PDF Supply stands by all of its repairs with a 1 year customer satisfaction warranty.
For more information on the IC697PWR711 120/240 VAC or 125 VDC, 100W Power Supply Module of the GE Fanuc 90-70 Series, please see the Datasheet User-Manual.
Common related search terms: Datasheet, Emerson, Manual, PDF, PLC, Price, Repair, Specification, Troubleshoot, User-Manual, Wiring,
PDF Electric & Supply Inc. sells new, new surplus and refurbished products which are sourced through independent channels. All warranties and support, if applicable, are with PDF Electric & Supply Inc. and not the manufacturer. PDF Electric & Supply Inc. is not an authorized distributor or representative for the listed manufacturers and makes no representations as to any quality control performed by any listed manufacturer on the products. The products listed on this website may vary as to their country of origin; the accessories, and other items included with the product; and the language used on the packaging, the parts, and any related instructions or printed material related to the products. This website is not sanctioned or approved by any manufacturer or tradename listed. Designated trademarks, brand names and brands appearing herein are the property of their respective owners.