1-919-535-3180 | 1-800-360-6802

GE / IP FANUC Series 90/30 In Stock

World's Largest Warehouse

of GE 90-30, Genius, and RX7i



Mon-Fri 8AM-5PM EST



Rated 4.6/5 Based on 16 ratings.

Rate your purchase of the IC697RCM711


SKU 2175137  UPC 0871213795454

All product names, trademarks, brands and logos used on this site are the property of their respective owners. PDF Supply is not an authorized distributor, reseller or representative of the products featured on this website. The depiction, description or sale of products featuring these names, trademarks, brands and logos is for identification purposes only and is not intended to indicate any affiliation with or authorization by any rights holder.

MSRP $6106


  ON SALE ! 

Save $3,118

2 in stock

✓  2 Year PDF Supply warranty

*Need a Specific Revision?

"Factory Sealed"

New Surplus


Save $4,118

1 in stock

✓  3 Year PDF Supply warranty

*What is New Surplus?

"Like New Condition"



Save $5,711

21 in stock

✓  2 Year PDF Supply warranty

*What is Remanufactured?

"Avg. Repair - 2 Days"

Repair Service


Save $5,811

5-10 Days

✓  2 Year PDF Supply warranty

*What is Fast Repair?

Product Description

The IC697RCM711 is a Redundancy Communications Module designed for the GE Fanuc 90-70 series
. The IC697RCM711 is a single slot module with five LEDs that emit the status of the board and system. The module is designed to offer a path for a synchronizing message from the active to the backup unit. The IC697RCM711 module is also the route for the transfer of I/O data shared between both units. There are two connecters, one located on the top of module and another on the bottom. The top connector is used for attaching the upstream BTM or BRM, and the bottom connector is not used. The IC697RCM711 module requires 0.7 amps of current and is configured using MS-DOS software. The module features a high speed parallel bus interface and supports configurations that are Hot Standby and Hot Standby CPU Redundancy system constructed.

The IC697RCM711 uses a single slot between slots 2-9. The aforementioned LEDs are labeled Board OK, Local Ready, Local Active, Remote Ready, and Remote Active. The IC697RCM module is also equipped with a pushbutton that allows the user to manually switch from the active unit to the backup unit, which permits maintenance for the previous active unit while the system is online. Once a switch is made, there will not be another switch allowed for 10 seconds by the system.  When installing the IC697RCM711 module, the user should refer to the Hot Standby CPU Redundancy User’s guide or the Enhanced User’s guide. The power on the rack needs to be turned off before installation. Once installed and the appropriate cable is connected, the power can be turned back on.

Technical Specifications

Module Type: Redundancy Communications
Number of Slots:   One (Single Slot)
# of LEDs: 5
Connects to: MS-DOS
Serial Ports: 2 (1 not used)
Current Required:    0.7 amps


Standby Redundancy Comm card IC697R IC697RC IC697RCM
ST. LOUIS, Feb. 1, 2019 – Emerson today announced it has completed the purchase of Intelligent Platforms from General Electric.

Common related search terms: ConfigurationDatasheetEmersonManualPDFPLCPriceRepairSpecificationTroubleshootUser-ManualWiring

All online orders placed before 4:30 PM EST “SHIPS SAME DAY FREE!" World’s largest warehouse of Factory Sealed GE 90-30 PLC, GENIUS I/O and RX7i PACSystem.highlight_off

PDF Electric & Supply Inc. sells new, new surplus and refurbished products which are sourced through independent channels. All warranties and support, if applicable, are with PDF Electric & Supply Inc. and not the manufacturer. PDF Electric & Supply Inc. is not an authorized distributor or representative for the listed manufacturers and makes no representations as to any quality control performed by any listed manufacturer on the products. The products listed on this website may vary as to their country of origin; the accessories, and other items included with the product; and the language used on the packaging, the parts, and any related instructions or printed material related to the products. This website is not sanctioned or approved by any manufacturer or tradename listed. Designated trademarks, brand names and brands appearing herein are the property of their respective owners.