GE / IP FANUC Series 90/30 In Stock
SKU 2172115 UPC 0359420178258
All product names, trademarks, brands and logos used on this site are the property of their respective owners. PDF Supply is not an authorized distributor, reseller or representative of the products featured on this website. The depiction, description or sale of products featuring these names, trademarks, brands and logos is for identification purposes only and is not intended to indicate any affiliation with or authorization by any rights holder.
Other Available Revisions for the IC200BEM002 IC200BEM002-AA/-AAIC200BEM002-BA/-BAIC200BEM002-CA/-CAIC200BEM002-DA/-DAIC200BEM002-EA/-EAIC200BEM002-FA/-FAIC200BEM002-HA/-HAIC200BEM002-JA/-JAIC200BEM002-KA/-KAIC200BEM002-LA/-LAIC200BEM002-MA/-MAIC200BEM002A/AIC200BEM002B/BIC200BEM002C/CIC200BEM002D/DIC200BEM002E/EIC200BEM002F/FIC200BEM002G/GIC200BEM002H/HIC200BEM002I/IIC200BEM002J/JIC200BEM002K/KIC200BEM002L/LIC200BEM002LT/LTIC200BEM002M/MIC200BEM002N/NIC200BEM002O/OIC200BEM002P/PIC200BEM002Q/QIC200BEM002R/RIC200BEM002S/SIC200BEM002T/TIC200BEM002U/UIC200BEM002V/VIC200BEM002W/WIC200BEM002X/XIC200BEM002Y/YIC200BEM002Z/Z
IC200BEM002 is a PLC Network Communications PROFIBUS-DP (Slave) Module from the GE Fanuc Versamax Series. This network style module offers 32 stations without repeaters or up to 125 stations with repeaters. The I/O data is set at 384 bytes on a 9 pin, D-sub connector. With a firmware version of 1.00, this network slave module has firmware residing in the FLASH memory that may be upgraded via serial download when a PC is connected to the serial port. Specifically, the Profibus network is software configurable from 1 to 125 at 9.6 Kbaud to 12 Mbaud, which is auto-detected. I/O data offers a 384 byte maximum with up to 244 bytes or either input or output data.
When installing the IC200BEM002, make sure to carefully inspect all containers and parts for damage. If anything is damaged, do not use the part as it may be unsafe. To install, simply click the communications carrier on the DIN rail. Make sure the connecting carriers are installed in the same section. The DIN rail must have a conductive, unpainted finish to properly ground the module. To install on the communications carrier, make sure the module is in the unlocked position, align the connectors, and press the NSIM down until the two tabs click into place; then lock the latch to secure. Finally, connect the communications bus, install additional modules as needed, and power up the system.
LED indicators are standard on the IC200BEM002 and will alert the user to proper installation and power source status.
|Module Type:||Network Slave Module|
|Number of Stations:||32 w/out repeaters, up to 125 with|
|I/O Data:||384 Bytes|
|Network Data Rate:||9.6 Kbaud to 12 Mbaud|
|Power Consumption:||460 mA from 5 V output|
Repair your IC200BEM002
For more information on the IC200BEM002 PLC Network Communications PROFIBUS-DP (Slave) Module from the GE Fanuc Versamax Series, please see the Datasheet User-Manual.
PDF Electric & Supply Inc. sells new, new surplus and refurbished products which are sourced through independent channels. All warranties and support, if applicable, are with PDF Electric & Supply Inc. and not the manufacturer. PDF Electric & Supply Inc. is not an authorized distributor or representative for the listed manufacturers and makes no representations as to any quality control performed by any listed manufacturer on the products. The products listed on this website may vary as to their country of origin; the accessories, and other items included with the product; and the language used on the packaging, the parts, and any related instructions or printed material related to the products. This website is not sanctioned or approved by any manufacturer or tradename listed. Designated trademarks, brand names and brands appearing herein are the property of their respective owners.